Magazine
Magpul PMAG 30 AR/M4 GEN M3
Magpul's 30-round polymer magazine for AR-15/M4 rifles in 5.56 NATO and .223 Remington, the third generation; the catalog's first 5.56 magazine.

- Weight
- 5 oz ± 0.05 oz Confirmedpublished: Magpul, PMAG 30 AR/M4 GEN M3 (MAG557), specifications, the maker, read Oct 2, 2026
- Lowest price
- $12.88 at Primary Arms, read Nov 21, 2026 (Black)
- Made for
- a 30-round polymer magazine for AR15/M4 compatible weapons chambered in 5.56x45 NATO / .223 Remington
- Maker's number
- MAG557
- Colours
- Black, Medium Coyote Tan, Modified Coyote Brown, ODG
- Drawn as
- modelled
In “Aero 5.56 carbine”, a build on the start page, as it is.
Its figures
Every figure the site draws and checks it by, with where it came from. Open one for each source's reading, and why one is used where they differ.
Overall height, feed lips to base7.5 in ± 0.1 in 190.5 mmConfirmedPublished: Magpul, PMAG 30 AR/M4 GEN M3 (MAG557), specifications, the maker, read Oct 2, 2026
Published “Length, max: 7.5 in.” used
Magpul, PMAG 30 AR/M4 GEN M3 (MAG557), specifications, the maker, read Oct 2, 2026 the page, harvested Oct 2, 2026
Magpul's 'Length, max', read as the height standing upright (its top level): the curve's diagonal would be about 1% more, which the ± covers. The patent's side elevation is scaled by it.
Body height below the feed-lip blockNo value yetMissingNo source yet
Onboarding checklist: Side view; overall_height minus the feed-lip block when the block is shared across a product line.
Feed-lip block heightNo value yetMissingNo source yet
Onboarding checklist.
Front to back at the body top2.528 in ± 0.035 in 64.2 mmProvisionalPhoto: US D681,151 S (Magpul, 'Firearm magazine with window'), FIG. 2 right side elevation, 300 dpi
Photo 2.528 in ± 0.035 in used
US D681,151 S (Magpul, 'Firearm magazine with window'), FIG. 2 right side elevation, 300 dpi, harvested
Scale: scale from magpul-pmag-30-gen-m3.overall_height = 7.5 in (y-extent 2599 px → 346.5 px/in). Read by width in y [-1.2, -0.6] of the traced outline (tools/trace.py); the body's front to back below the feed lips, where it is straight (it fits the magwell there)
Onboarding checklist: Side view; same calibration as the heights.
The spine's rear face where it stands in the well, ahead of the tip of the stop on the spine below it (the side outline's rearmost point)0.066 in ± 0.02 in 1.7 mmProvisionalPhoto: US D681,151 S (Magpul, 'Firearm magazine with window'), FIG. 2 right side elevation, 300 dpi
Photo 0.066 in ± 0.02 in used
US D681,151 S (Magpul, 'Firearm magazine with window'), FIG. 2 right side elevation, 300 dpi, harvested
Scale: scale from magpul-pmag-30-gen-m3.overall_height = 7.5 in (y-extent 2599 px → 346.5 px/in). Read by x_min in y [-1.2, -0.6] of the traced outline (tools/trace.py); the spine's rear face where the body is straight (it stands in the magwell there), ahead of the outline's rearmost point: the tip of the stop on the spine just under the well, where the outline's origin is
Where its anchor is (2026-10-05). The side outline's origin is its rearmost point, and that is the tip of the stop standing out of the spine just under the magwell, not the spine: seated by it, the magazine stood this far forward, its front face 0.06 in through the well's front wall (std.ar15.magwell_front_inner_x).
Magazine catch notch (left side), its upper edge below the feed lips' top1.07 in ± 0.04 in 27.2 mmCorroboratedPhoto: Magpul's own photo of the left side, on white, the magazine leaning 7.8°, 1200 px
Photo 1.07 in ± 0.04 in used
Magpul's own photo of the left side, on white, the magazine leaning 7.8°, 1200 px, harvested
Scale: magpul-pmag-30-gen-m3.overall_height = 7.5 in over the photo's 1065 px from the feed lips' top to the lowest point, both measured down the body's own axis (the spine's lean: its edge at columns 760, 774, 787, 801 on rows 150 to 450): 142 px/in. Read by the notch is the dark rounded window at columns 632 to 702; its upper edge at row 215, the feed lips' top at (700, 57): 152 px down the axis
Photo 1.12 in ± 0.04 in
US D681,151 S (Magpul, 'Firearm magazine with window'), FIG. 3 left side elevation, 300 dpi, harvested
Scale: magpul-pmag-30-gen-m3.overall_height = 7.5 in over the drawing's 2572 px. Read by the notch's upper edge at row 832, the top at row 448 (the same review's reading)
A design patent's drawing of the window model (MAG556), the same outside: a second reading, not the product's own.
Magpul's photograph of the product itself; the patent's drawing agrees within the two readings' ± (0.05 apart).
What seats it: the notch's upper edge hangs on the lower's catch (2026-10-05; until then it was hung where the catalog's .22 magazine's feed lips are, 0.37 in too high, its lips above the bore's axis). Both readings are scaled by Magpul's 7.5 in read as the height standing upright; if that is the length along the curve they are 1% less.
Magazine catch notch (left side), its height0.25 in ± 0.02 in 6.3 mmCorroboratedPhoto: Magpul's own photo of the left side, on white, the magazine leaning 7.7°, 1200 px
Photo 0.25 in ± 0.02 in used
Magpul's own photo of the left side, on white, the magazine leaning 7.7°, 1200 px, harvested
Scale: the photo's silhouette fitted to the traced side outline, so x is from the outline's rearmost point and y from the feed lips' top. Read by the window is the darkest thing on the side (luminance under 35 of 255): the 1st to the 99th percentile of its pixels down the body, y -1.084 to -1.334 (its upper edge 0.014 in lower than catch_notch_top's reading of the same photo, within that one's ±); ± 2 px and the threshold (at 45 the block's shadow under it joins it)
Photo 0.26 in ± 0.012 in
US D681,151 S (Magpul, 'Firearm magazine with window'), FIG. 3 left side elevation, 300 dpi, harvested
Scale: magpul-pmag-30-gen-m3.overall_height = 7.5 in over the drawing's 2572 px (rows 447 to 3019): 342.9 px/in; x from its rearmost column, 1895. Read by the rounded rectangle's upper and lower lines on column 1600: rows 830 to 833 and 919 to 922, centre to centre 89 px
The window model's drawing (MAG556), the same outside: a second reading.
Magpul's photograph of the product itself; the patent's drawing agrees within the two readings' ±.
The window the catch comes into: as tall as the slot it comes through in a lower (std.ar15.mag_catch_slot_h, 0.252 in). Scaled as catch_notch_top is.
Magazine catch notch (left side), its rear end ahead of the side outline's rearmost point0.55 in ± 0.03 in 14 mmCorroboratedPhoto: Magpul's own photo of the left side, on white, the magazine leaning 7.7°, 1200 px
Photo 0.55 in ± 0.03 in used
Magpul's own photo of the left side, on white, the magazine leaning 7.7°, 1200 px, harvested
Scale: the photo's silhouette fitted to the traced side outline, so x is from the outline's rearmost point and y from the feed lips' top. Read by the window's dark pixels (luminance under 35), the 1st percentile along the body: x 0.548; ± 2 px, the threshold and the fit
Photo 0.57 in ± 0.02 in
US D681,151 S (Magpul, 'Firearm magazine with window'), FIG. 3 left side elevation, 300 dpi, harvested
Scale: magpul-pmag-30-gen-m3.overall_height = 7.5 in over the drawing's 2572 px (rows 447 to 3019): 342.9 px/in; x from its rearmost column, 1895. Read by the rounded rectangle's rear line on row 878: columns 1697 to 1700, 196.5 px ahead of the rearmost column
The window model's drawing: a second reading.
Magpul's photograph of the product itself; the patent's drawing agrees within the two readings' ±.
Magazine catch notch (left side), its front end ahead of the side outline's rearmost point1.06 in ± 0.03 in 26.9 mmCorroboratedPhoto: Magpul's own photo of the left side, on white, the magazine leaning 7.7°, 1200 px
Photo 1.06 in ± 0.03 in used
Magpul's own photo of the left side, on white, the magazine leaning 7.7°, 1200 px, harvested
Scale: the photo's silhouette fitted to the traced side outline, so x is from the outline's rearmost point and y from the feed lips' top. Read by the window's dark pixels (luminance under 35), the 99th percentile along the body: x 1.060 (the window 0.51 in long); ± 2 px, the threshold and the fit
Photo 1.1 in ± 0.02 in
US D681,151 S (Magpul, 'Firearm magazine with window'), FIG. 3 left side elevation, 300 dpi, harvested
Scale: magpul-pmag-30-gen-m3.overall_height = 7.5 in over the drawing's 2572 px (rows 447 to 3019): 342.9 px/in; x from its rearmost column, 1895. Read by the rounded rectangle's front line on row 878: columns 1518 to 1521, 375.5 px ahead of the rearmost column (the rectangle 0.52 in long)
The window model's drawing: a second reading.
Magpul's photograph of the product itself; the patent's drawing reads 0.035 in further forward, within the two readings' ±.
The block under the catch notch (left side), standing out of the side0.054 in ± 0.006 in 1.4 mmCorroboratedPhoto: US D681,151 S (Magpul), FIG. 6 front elevation, 300 dpi
Photo 0.054 in ± 0.006 in used
US D681,151 S (Magpul), FIG. 6 front elevation, 300 dpi, harvested
Scale: magpul-pmag-30-gen-m3.overall_height = 7.5 in over the figure's 2440 px (rows 467 to 2907): 325.3 px/in. Read by rows 918 to 957: the block's outer line at columns 950 to 954, the side's at 934 to 937: 17.5 px, centre to centre; its top a level line at rows 914 to 916 (1.377 in under the top of the lips), its chamfer from row 957 back to the side at row 981; ± 2 px
The window model's drawing (MAG556).
Photo 0.053 in ± 0.006 in
US D681,151 S (Magpul), FIG. 7 rear elevation, on the same sheet, 300 dpi, harvested
Scale: magpul-pmag-30-gen-m3.overall_height = 7.5 in over the figure's 2440 px (rows 467 to 2907): 325.3 px/in. Read by rows 918 to 957: the block's outer line at columns 1597 to 1601, the side's at 1615 to 1618: 17.25 px; its top at rows 914 to 916, its chamfer from row 957 to row 984; ± 2 px
The window model's drawing.
The two elevations agree within a third of a pixel; the front one is the figure the front outline is traced from.
A block as long as the notch's middle stands under it on the left side, its top a flat ledge at the notch's lower edge and its lower end chamfered back into the side: the front and rear elevations have it in profile (on the right of FIG. 6, a front elevation, and the left of FIG. 7), the left elevation and the top and bottom plans in outline. On this magazine: Magpul's left-side photo has its outline under the window with a darker band along its lower end (the shadow under something that stands out, lit from above), Magpul's close view of the top (1dd728b26229) a lit ledge under the window, Primary Arms' view from above the top (53b35012a3a4) a lit face beyond the window; none shows it in profile, so how far it stands is the patent's. NOT RECONCILED WITH THE WELL: seated by its notch (catch_notch_top on the catch's upper face), the block is below the catch's slot in a lower's left wall (std.ar15.mag_catch_slot_h, 0.252 in, the notch's own height), where the well is .898 wide (std.ar15.magwell_width), and a body as wide as the patent's with this block on it is 0.97. As drawn it stands 0.06 in into that wall. What is misread isn't found: the magazine's width in the well is 0.914 at this scale, 0.016 more than the well's already (the patent's drawing scaled by Magpul's 7.5 in).
The block under the catch notch, from the notch's lower edge down to where it is back in the side0.21 in ± 0.012 in 5.3 mmCorroboratedPhoto: US D681,151 S (Magpul, 'Firearm magazine with window'), FIG. 3 left side elevation, 300 dpi
Photo 0.21 in ± 0.012 in used
US D681,151 S (Magpul, 'Firearm magazine with window'), FIG. 3 left side elevation, 300 dpi, harvested
Scale: magpul-pmag-30-gen-m3.overall_height = 7.5 in over the drawing's 2572 px (rows 447 to 3019): 342.9 px/in; x from its rearmost column, 1895. Read by the lower rectangle on column 1600: from the rounded rectangle's lower line (rows 919 to 922) to its own lower line (rows 991 to 994), 72 px centre to centre
The window model's drawing.
Photo 0.203 in ± 0.012 in
US D681,151 S (Magpul), FIG. 6 front elevation, 300 dpi, harvested
Scale: magpul-pmag-30-gen-m3.overall_height = 7.5 in over the figure's 2440 px (rows 467 to 2907): 325.3 px/in. Read by from its top (rows 914 to 916) to where its chamfer meets the side (row 981): 66 px
The window model's drawing.
The view that has the block's whole outline; the front elevation agrees within its ±. On Magpul's photo of this magazine its top is the window's lower edge (y -1.335) and the dark under its lower end runs on to -1.65: its chamfer and its shadow together, so its end isn't read there.
The block under the catch notch, the height of the chamfer at its lower end0.074 in ± 0.01 in 1.9 mmCorroboratedPhoto: US D681,151 S (Magpul), FIG. 6 front elevation, 300 dpi
Photo 0.074 in ± 0.01 in used
US D681,151 S (Magpul), FIG. 6 front elevation, 300 dpi, harvested
Scale: magpul-pmag-30-gen-m3.overall_height = 7.5 in over the figure's 2440 px (rows 467 to 2907): 325.3 px/in. Read by the outer line leaves its column at row 957 and meets the side's at row 981: 24 px
The window model's drawing.
Photo 0.083 in ± 0.01 in
US D681,151 S (Magpul), FIG. 7 rear elevation, on the same sheet, 300 dpi, harvested
Scale: magpul-pmag-30-gen-m3.overall_height = 7.5 in over the figure's 2440 px (rows 467 to 2907): 325.3 px/in. Read by the outer line leaves its column at row 957 and meets the side's at row 984: 27 px
The window model's drawing.
The figure the block's stand-off is adopted from; the rear elevation agrees within its ±.
The block under the catch notch, its length along the magazine (front to back)0.375 in ± 0.03 in 9.5 mmCorroboratedPhoto: Magpul's own photo of the left side, on white, the magazine leaning 7.7°, 1200 px
Photo 0.375 in ± 0.03 in used
Magpul's own photo of the left side, on white, the magazine leaning 7.7°, 1200 px, harvested
Scale: the photo's silhouette fitted to the traced side outline, so x is from the outline's rearmost point and y from the feed lips' top. Read by the dark lines of its two ends on three lines across it (y -1.40, -1.46, -1.52, each the mean of ± 0.02): x 0.619 and 0.994 to 1.000; ± 2 px and the fit
Photo 0.4 in ± 0.02 in
US D681,151 S (Magpul, 'Firearm magazine with window'), FIG. 3 left side elevation, 300 dpi, harvested
Scale: magpul-pmag-30-gen-m3.overall_height = 7.5 in over the drawing's 2572 px (rows 447 to 3019): 342.9 px/in; x from its rearmost column, 1895. Read by the lower rectangle's two side lines, columns 1541 and 1678: 137 px
The window model's drawing.
Magpul's photograph of the product itself; the patent's drawing agrees within the two readings' ±.
Centred under the notch in both: its middle 0.807 from the outline's rearmost point on the photo (the window's 0.804), 0.833 on the patent's drawing (its rounded rectangle's 0.834).
The side panels' floors below the grip frame's ribs and bands0.025 in ± 0.006 in 0.6 mmCorroboratedPhoto: US D681,151 S (Magpul), FIG. 6 front elevation, 300 dpi
Photo 0.025 in ± 0.006 in used
US D681,151 S (Magpul), FIG. 6 front elevation, 300 dpi, harvested
Scale: magpul-pmag-30-gen-m3.overall_height = 7.5 in over the figure's 2440 px (rows 467 to 2907): 325.3 px/in. Read by between the bands (rows 1499 to 1691, 1811 to 1991, 2123 to 2291): the frame's silhouette at columns 629 to 631 and 943 to 946, the panels' floor line at 637 to 639 and 935 to 938: 8.0 px each side, centre to centre; ± 2 px for two lines 3 px thick
The window model's drawing (MAG556): the same frame at the front, where this magazine's panels lie on the patent's.
Photo 0.029 in ± 0.006 in
US D681,151 S (Magpul), FIG. 7 rear elevation, on the same sheet, 300 dpi, harvested
Scale: magpul-pmag-30-gen-m3.overall_height = 7.5 in over the figure's 2440 px (rows 467 to 2907): 325.3 px/in. Read by between the bands (rows 1547 to 1763, 1907 to 2123, 2231 to 2447): the frame's silhouette at columns 1606 to 1609 and 1920 to 1923, the panels' floor line at 1615 to 1620 and 1910 to 1914: 9.8 and 9.3 px, centre to centre; ± 2 px
The window model's drawing: the rear column's panels at the spine.
The figure the front outline is traced from, so the floors come out where it has them: in the plane of the sides above the frame. The rear elevation reads 0.004 in more, within both readings' ±.
How far the frame stands out of each side (2026-10-05). The front and rear columns' panels run out to the front face and to the spine between the bands, so the front and rear elevations show their floors in profile: a line inside the frame's silhouette that runs on, straight, from the silhouette of the plain sides above the frame (FIG. 6: 638.5 and 936 above, 638 and 936.5 between the bands). The floors are the body's own sides carried down, and the frame is what stands on them. The middle column's panels and the one under the last band are closed all round and show in no profile: they are taken to the same floor (Primary Arms' photo from above the top, 53b35012a3a4, shows their walls as tall as the step at the frame's upper edge beside them). The bands' silhouette is the ribs' within a pixel in both figures: on the sides they are one level.
A side panel's wall, from its rim on the frame in to its floor's edge, as the side view has it0.026 in ± 0.006 in 0.7 mmProvisionalPhoto: US D681,151 S (Magpul, 'Firearm magazine with window'), FIG. 2 right side elevation, 300 dpi
Photo 0.026 in ± 0.006 in used
US D681,151 S (Magpul, 'Firearm magazine with window'), FIG. 2 right side elevation, 300 dpi, harvested
Scale: scale from magpul-pmag-30-gen-m3.overall_height = 7.5 in (y-extent 2599 px → 346.6 px/in). Read by the two lines round each panel, its rim and its floor's edge: 8.5 and 9.5 px apart on the first middle panel's upper edge (columns 1150, 1250), 8.5 and 9.5 on its rear and front edges (row 1650), 9 on the first rear panel's front edge; ± 2 px
The window model's drawing (MAG556).
About as far across as the panel is deep: a wall near 45°. On Magpul's photo of this magazine (3eded591002b) the panels' edges are soft dark lines 3 to 4 px wide of 141.5 px/in, 0.02 to 0.03 in: the same.
A side panel's corners, their radius at the middle of the wall0.08 in ± 0.02 in 2 mmProvisionalPhoto: Magpul's own photo of the left side, on white, the magazine leaning 7.7°, 1200 px
Photo 0.08 in ± 0.02 in used
Magpul's own photo of the left side, on white, the magazine leaning 7.7°, 1200 px, harvested
Scale: 141.5 px/in (the fit of its silhouette to the side outline). Read by the round where two edges' dark lines meet, on tiles enlarged four times: 9.5 px on the first front panel, 12.5 on the first middle one, 10 on the first rear one; the ± covers their spread and ± 2 px
The tab on the grip frame's upper edge, the round of its two upper corners0.03 in ± 0.015 in 0.8 mmProvisionalPhoto: Magpul's own photo of the left side, on white, the magazine leaning 7.7°, 1200 px
Photo 0.03 in ± 0.015 in used
Magpul's own photo of the left side, on white, the magazine leaning 7.7°, 1200 px, harvested
Scale: the left trace's own placement of this photo (profiles.left: turned 7.66°, magpul-pmag-30-gen-m3.overall_height = 7.5 in over the silhouette's 1064 px, 141.9 px/in; x from its rearmost point, y from the feed lips' top), in the plane of the side. Read by on a tile enlarged seven times: the dark line turns from the tab's top (row 417) into each side (columns 471 and 499) within 3 to 5 px; ± covers the pick and that a line 3 px wide hides a smaller round
The tab stands up from the frame's upper edge 0.36 in behind the front face, 0.2 in long and 0.5 high (profiles.left, above_frame: its four middle corners). It is a piece of the side at the side's own width, standing where the side leans in toward the front face (nose_taper_length): the front elevation, FIG. 6, has its face on the plain side's silhouette (0.460 and 0.458 in from the middle at y -2.5 and -2.65, as at -2.2 over it; its inner edges at 0.425 and 0.394), and on this photo no line crosses its feet (a profile down its middle, and one each side of that, is within 2 to 3 levels of flat where the edge beside it is 6 to 9 darker): the frame's face comes down to the plain side's at its upper edge there, as the front elevation's silhouette does (0.474 at y -2.88, 0.482 at -2.93, 0.485 at -3.2). Where its sides run into the edge the photo has them turn out, about as a side panel's corner (side_panel_corner_radius): not drawn, its walls stand square on the edge.
The dot matrix under the last band: its blocks, each side4ProvisionalPhoto: Magpul's own photo of the left side, on white, the magazine leaning 7.7°, 1200 px
Photo 4 count used
Magpul's own photo of the left side, on white, the magazine leaning 7.7°, 1200 px, harvested
Scale: the left trace's own placement of this photo (profiles.left: turned 7.66°, magpul-pmag-30-gen-m3.overall_height = 7.5 in over the silhouette's 1064 px, 141.9 px/in; x from its rearmost point, y from the feed lips' top), in the plane of the side. Read by a profile of the luminance along the matrix (0.4 in wide, 14.45° to the magazine's level): twelve lit walls and twelve dark ones in four threes, the threes 0.354 in apart (3.5 of the dimples' own pitch); the same four on Primary Arms' photo of the right side (8664c534ce73) and on Magpul's feature image of it (2dc1cc9f8264)
Magpul's sheet: "a paint pen dot matrix has been added to the bottom panel of the body". Its diagram of the matrix (a copy on file, "MAGPUL DOT MATRIX DIAGRAM") draws every character on a block of three by five squares. The patent's FIG. 2 and FIG. 3 draw the same four blocks.
The dot matrix: the columns of dimples in a block3ProvisionalPhoto: Magpul's own photo of the left side, on white, the magazine leaning 7.7°, 1200 px
Photo 3 count used
Magpul's own photo of the left side, on white, the magazine leaning 7.7°, 1200 px, harvested
Scale: the left trace's own placement of this photo (profiles.left: turned 7.66°, magpul-pmag-30-gen-m3.overall_height = 7.5 in over the silhouette's 1064 px, 141.9 px/in; x from its rearmost point, y from the feed lips' top), in the plane of the side. Read by the same profile: three lit walls and three dark ones to a block, 0.101 to 0.102 in apart
The dot matrix: the rows of dimples in a block5ProvisionalPhoto: Magpul's own photo of the left side, on white, the magazine leaning 7.7°, 1200 px
Photo 5 count used
Magpul's own photo of the left side, on white, the magazine leaning 7.7°, 1200 px, harvested
Scale: the left trace's own placement of this photo (profiles.left: turned 7.66°, magpul-pmag-30-gen-m3.overall_height = 7.5 in over the silhouette's 1064 px, 141.9 px/in; x from its rearmost point, y from the feed lips' top), in the plane of the side. Read by a profile down each block's middle column (0.06 in wide, square to the rows), from the panel's upper edge to its lower: five dark walls in each of the four blocks, 0.100 to 0.101 in apart
The dot matrix: from one dimple's middle to the next, along a row and down a column0.101 in ± 0.003 in 2.6 mmProvisionalPhoto: Magpul's own photo of the left side, on white, the magazine leaning 7.7°, 1200 px
Photo 0.101 in ± 0.003 in used
Magpul's own photo of the left side, on white, the magazine leaning 7.7°, 1200 px, harvested
Scale: the left trace's own placement of this photo (profiles.left: turned 7.66°, magpul-pmag-30-gen-m3.overall_height = 7.5 in over the silhouette's 1064 px, 141.9 px/in; x from its rearmost point, y from the feed lips' top), in the plane of the side. Read by along the rows, wall to like wall: 0.104, 0.100; 0.100, 0.102; 0.102, 0.102; 0.100, 0.103 (lit walls 0.102, 0.102; 0.102, 0.100; 0.104, 0.102; 0.102, 0.101); down the columns 0.100, 0.100, 0.103, 0.100 and the like in the other three blocks; ± is the spread
One figure for both: the lattice is square. The blocks are 3.5 of it apart (0.354 in read), which the model takes from the blocks' own corners (profiles.left, dot_blocks).
The dot matrix: a dimple across, wall to wall0.068 in ± 0.008 in 1.7 mmProvisionalPhoto: Magpul's own photo of the left side, on white, the magazine leaning 7.7°, 1200 px
Photo 0.068 in ± 0.008 in used
Magpul's own photo of the left side, on white, the magazine leaning 7.7°, 1200 px, harvested
Scale: the left trace's own placement of this photo (profiles.left: turned 7.66°, magpul-pmag-30-gen-m3.overall_height = 7.5 in over the silhouette's 1064 px, 141.9 px/in; x from its rearmost point, y from the feed lips' top), in the plane of the side. Read by the lit wall to the dark wall of one dimple along the rows: 0.067, 0.069, 0.067; 0.069, 0.067, 0.069; 0.069, 0.067, 0.067; 0.069, 0.067, 0.069 (the land between two dimples 0.033 to 0.035); down the columns the land is 0.031 to 0.035, which leaves 0.066 to 0.070. Each is the middle of a wall's line to the middle of the next: ± is 1 px
Square, sunk into the panel's floor: on the photo each has its lit wall toward the spine and its dark one toward the front, as the panel's own walls have theirs, and Magpul's feature image of the right side (2dc1cc9f8264) has every dimple's shadow on the wall toward the light. HOW DEEP isn't in any view (no elevation draws a dimple in profile): the model sinks them six tenths of side_panel_depth, their walls' shadows on this photo being a little over half as strong as the panel's own wall's beside them (7 to 9 levels against 13). Its four walls are drawn leaning as a panel's do, as far across as the dimple is deep, about this figure (ASSUMED: on the photo a wall is a line a pixel or two wide). Their corners' round (the patent draws them round) is under the photo's grain and isn't drawn.
The front strip's bars, how far they stand out of the strip0.017 in ± 0.004 in 0.4 mmCorroboratedPhoto: Magpul's own photo of the left side, on white, the magazine leaning 7.7°, 1200 px
Photo 0.017 in ± 0.004 in used
Magpul's own photo of the left side, on white, the magazine leaning 7.7°, 1200 px, harvested
Scale: the left trace's own placement of this photo (profiles.left: turned 7.66°, magpul-pmag-30-gen-m3.overall_height = 7.5 in over the silhouette's 1064 px, 141.9 px/in); the teeth are on the silhouette's own edge, the magazine's mid-plane. Read by the silhouette's front edge found to a quarter pixel on lines of constant height; each tooth's top over the edge on both sides of it: 0.018, 0.018, 0.015, 0.017, 0.016 in the first row, 0.020, 0.016, 0.014, 0.015, 0.015 in the second (0.019, 0.018, 0.018, 0.017, 0.017 and 0.019, 0.019, 0.018, 0.016, 0.016 on Primary Arms' photo of the right side, 8664c534ce73, at 170 px/in). The lower rows read 0.009 to 0.012 here, their edge softened by the photo's cut-out; ± is the spread of the upper two
Photo 0.018 in ± 0.004 in
US D681,151 S (Magpul, 'Firearm magazine with window'), FIG. 2 right side elevation, 300 dpi, harvested
Scale: the side trace's own placement of the figure (magpul-pmag-30-gen-m3.overall_height = 7.5 in over 2599 px: 346.6 px/in; x from its rearmost point). Read by the figure's front edge, its outer line's outside: the teeth of the first row stand 0.015 to 0.020 over the edge beside them
The window model's drawing (MAG556), the same outside.
Magpul's photograph of the product itself; the patent's drawing agrees within a thousandth.
The bars are ridges across the front strip between the bands, five to a row and four in the last (profiles.left, bars_front: where each is). The bands stand as far out of the strip as out of the sides (0.02 to 0.025 in on the same edge: side_panel_depth).
The spine's bars, how far they stand out of the spine0.022 in ± 0.004 in 0.6 mmCorroboratedPhoto: Magpul's own photo of the left side, on white, the magazine leaning 7.7°, 1200 px
Photo 0.022 in ± 0.004 in used
Magpul's own photo of the left side, on white, the magazine leaning 7.7°, 1200 px, harvested
Scale: the left trace's own placement of this photo (profiles.left: turned 7.66°, magpul-pmag-30-gen-m3.overall_height = 7.5 in over the silhouette's 1064 px, 141.9 px/in); the teeth are on the silhouette's own edge, the magazine's mid-plane. Read by the silhouette's rear edge, the same way: 0.022, 0.025, 0.023, 0.025 under the stop, 0.020, 0.021, 0.020, 0.022, 0.022 under the rib, 0.018, 0.016, 0.018, 0.019 in the last row (0.021 to 0.023 and 0.016 to 0.017 on Primary Arms' photo of the right side)
Photo 0.016 in ± 0.004 in
US D681,151 S (Magpul, 'Firearm magazine with window'), FIG. 2 right side elevation, 300 dpi, harvested
Scale: the side trace's own placement of the figure (magpul-pmag-30-gen-m3.overall_height = 7.5 in over 2599 px: 346.6 px/in; x from its rearmost point). Read by the figure's rear edge: its teeth stand 0.014 to 0.017 over the edge beside them
The window model's drawing (MAG556), the same outside.
Magpul's photograph of the product itself, which Primary Arms' agrees with; the drawing's teeth are a little lower, within the two readings' ±.
The same ridges on the spine (profiles.left, bars_spine). The long rib down the spine's middle in the second row stands as far: no tooth shows there from the side.
A bar of the front strip or the spine, its thickness along the magazine0.036 in ± 0.012 in 0.9 mmCorroboratedPhoto: Magpul's own photo of the left side, on white, the magazine leaning 7.7°, 1200 px
Photo 0.036 in ± 0.012 in used
Magpul's own photo of the left side, on white, the magazine leaning 7.7°, 1200 px, harvested
Scale: the left trace's own placement of this photo (profiles.left: turned 7.66°, magpul-pmag-30-gen-m3.overall_height = 7.5 in over the silhouette's 1064 px, 141.9 px/in); the teeth are on the silhouette's own edge, the magazine's mid-plane. Read by each tooth's length at half its height on the silhouette's edges: 0.036 to 0.048 on the front (softened by the cut-out), 0.024 to 0.032 on the spine; ± covers both
Photo 0.034 in ± 0.006 in
US D681,151 S (Magpul), FIG. 6 front elevation, 300 dpi, harvested
Scale: magpul-pmag-30-gen-m3.overall_height = 7.5 in over the figure's 2437 px (rows 467 to 2907, less a line's weight): 324.9 px/in; across from the figure's own middle column. Read by a bar's two lines down a column 0.1 in off the middle: rows 1482.8 to 1494.1, 1528.1 to 1539.1, 1618.6 to 1629.6 on the front elevation (0.035, 0.034, 0.034), and 0.033 between the like lines of the rear elevation's; ± 2 px
The window model's drawing (MAG556), the same outside.
The product's own teeth in profile; the drawing's two elevations agree within two thousandths.
The front strip: the flat of the grip frame's front face, between the rounds into its sides0.44 in ± 0.012 in 11.2 mmProvisionalPhoto: US D681,151 S (Magpul), FIG. 6 front elevation, 300 dpi
Photo 0.44 in ± 0.012 in used
US D681,151 S (Magpul), FIG. 6 front elevation, 300 dpi, harvested
Scale: magpul-pmag-30-gen-m3.overall_height = 7.5 in over the figure's 2437 px (rows 467 to 2907, less a line's weight): 324.9 px/in; across from the figure's own middle column. Read by the two lines down the front between the bands: columns 858.5 and 715.5 on rows 1515, 1538 and 2191 (0.220 each side of the middle); 857.5 and 717.2 across a band (0.217, 0.215); ± 2 px each
The window model's drawing (MAG556), the same outside.
What the bars lie across: FIG. 6 draws each bar from one of these two lines to the other. On Primary Arms' view of the front (53b35012a3a4) the bars run across the flat and stop where the face turns into the sides.
The grip frame's front corners: how far behind the front face a side begins to turn in0.115 in ± 0.012 in 2.9 mmProvisionalPhoto: US D681,151 S (Magpul, 'Firearm magazine with window'), FIG. 2 right side elevation, 300 dpi
Photo 0.115 in ± 0.012 in used
US D681,151 S (Magpul, 'Firearm magazine with window'), FIG. 2 right side elevation, 300 dpi, harvested
Scale: the side trace's own placement of the figure (magpul-pmag-30-gen-m3.overall_height = 7.5 in over 2599 px: 346.6 px/in; x from its rearmost point). Read by across the first row at y -3.4: the thin line inside the front panel at x 2.620, the front edge beside the teeth at 2.732 (0.112); across the third at y -5.2: 2.898 and 3.018 (0.120); ± 3 px
The window model's drawing (MAG556), the same outside.
With front_strip_width, the round of the frame's front corners: a side panel's floor runs forward flat to this far behind the front face and then turns in to the front strip's edge. No view has the turn in section; it is drawn as a quarter of an ellipse between the two (ASSUMED: FIG. 6 has three lines down it, at 0.358, 0.397 and 0.426 in from the middle, which a plain round wouldn't have).
The spine: the strip that stands behind the body's rear shoulders, its width0.442 in ± 0.012 in 11.2 mmProvisionalPhoto: US D681,151 S (Magpul), FIG. 7 rear elevation, on the same sheet, 300 dpi
Photo 0.442 in ± 0.012 in used
US D681,151 S (Magpul), FIG. 7 rear elevation, on the same sheet, 300 dpi, harvested
Scale: magpul-pmag-30-gen-m3.overall_height = 7.5 in over the figure's 2437 px (rows 467 to 2907, less a line's weight): 324.9 px/in; across from the figure's own middle column. Read by the two lines down the rear: columns 1693.3 and 1836.5 on rows 989, 1557, 1622, 1964, 2354 and 2614 (0.221, and 0.219 to 0.220, each side of the middle); ± 2 px each
The window model's drawing (MAG556), the same outside.
The spine is narrower than the body: it runs in the well's spine slot (std.ar15.magwell_spine_slot_width, .470) and goes on down the grip frame at the same width, carrying the bars and the rib. Primary Arms' view from the rear quarter (b279a01fae08) shows it standing behind the shoulders from the feed-lip block to the floorplate.
The long rib down the spine's middle (second row), and the stop's gusset over the first row: their width0.151 in ± 0.012 in 3.8 mmProvisionalPhoto: US D681,151 S (Magpul), FIG. 7 rear elevation, on the same sheet, 300 dpi
Photo 0.151 in ± 0.012 in used
US D681,151 S (Magpul), FIG. 7 rear elevation, on the same sheet, 300 dpi, harvested
Scale: magpul-pmag-30-gen-m3.overall_height = 7.5 in over the figure's 2437 px (rows 467 to 2907, less a line's weight): 324.9 px/in; across from the figure's own middle column. Read by columns 1740.0 and 1789.3 on row 1557 (the gusset), 1740.0 and 1789.0 on rows 1964 and 2012 (the rib): 0.077 and 0.075 each side of the middle; ± 2 px each
The window model's drawing (MAG556), the same outside.
FIG. 7 draws both between the same two lines: the gusset under the over-travel stop from its ledge down to 3.5 in under the top, the rib from the first band under it to the next. On the side photo the gusset is the slope from the stop's tip down to the spine (3.2 to 3.48 in under the top), and the rib is the straight stretch of the spine's edge from 4.11 to 5.36 with no tooth on it.
The spine's strip in the grip frame: how far it stands behind the shoulder beside it0.07 in ± 0.012 in 1.8 mmProvisionalPhoto: US D681,151 S (Magpul, 'Firearm magazine with window'), FIG. 2 right side elevation, 300 dpi
Photo 0.07 in ± 0.012 in used
US D681,151 S (Magpul, 'Firearm magazine with window'), FIG. 2 right side elevation, 300 dpi, harvested
Scale: the side trace's own placement of the figure (magpul-pmag-30-gen-m3.overall_height = 7.5 in over 2599 px: 346.6 px/in; x from its rearmost point). Read by along lines square to the spine's edge through the first and third rows: the first line ahead of the edge at 0.074 and 0.068 in; ± 3 px
The window model's drawing (MAG556), the same outside.
Between the bands the rear panels run round the rear corners onto a shoulder, and the spine's strip stands behind it by this.
The grip frame's rear corners: from the shoulder beside the spine to where a side begins to turn in0.12 in ± 0.015 in 3 mmProvisionalPhoto: US D681,151 S (Magpul, 'Firearm magazine with window'), FIG. 2 right side elevation, 300 dpi
Photo 0.12 in ± 0.015 in used
US D681,151 S (Magpul, 'Firearm magazine with window'), FIG. 2 right side elevation, 300 dpi, harvested
Scale: the side trace's own placement of the figure (magpul-pmag-30-gen-m3.overall_height = 7.5 in over 2599 px: 346.6 px/in; x from its rearmost point). Read by the same two lines: the third line ahead of the spine's edge at 0.199 and 0.182 in, less the shoulder's 0.074 and 0.068 (0.125, 0.114); ± 4 px
The window model's drawing (MAG556), the same outside.
With rear_shoulder_width, the round of the frame's rear corners, drawn as a quarter of an ellipse (ASSUMED, as the front's).
The grip frame's rear: the width over the two shoulders beside the spine, where the rounds into the sides begin0.554 in ± 0.012 in 14.1 mmProvisionalPhoto: US D681,151 S (Magpul), FIG. 7 rear elevation, on the same sheet, 300 dpi
Photo 0.554 in ± 0.012 in used
US D681,151 S (Magpul), FIG. 7 rear elevation, on the same sheet, 300 dpi, harvested
Scale: magpul-pmag-30-gen-m3.overall_height = 7.5 in over the figure's 2437 px (rows 467 to 2907, less a line's weight): 324.9 px/in; across from the figure's own middle column. Read by the strongest line outside the spine's on each side: columns 1674.5 and 1854.5 on rows 1557, 1622, 1964, 2354 and 2614 (0.278 and 0.276 each side of the middle); ± 2 px each
The window model's drawing (MAG556), the same outside.
The spine above the grip frame (in the well): how far it stands behind the body's rear shoulders0.101 in ± 0.012 in 2.6 mmProvisionalPhoto: US D681,151 S (Magpul, 'Firearm magazine with window'), FIG. 2 right side elevation, 300 dpi
Photo 0.101 in ± 0.012 in used
US D681,151 S (Magpul, 'Firearm magazine with window'), FIG. 2 right side elevation, 300 dpi, harvested
Scale: the side trace's own placement of the figure (magpul-pmag-30-gen-m3.overall_height = 7.5 in over 2599 px: 346.6 px/in; x from its rearmost point). Read by across the plain side at y -1.6 (a band 0.4 in high): the spine's edge at x 0.065, lines at 0.120, 0.166, 0.206 and 0.255; the shoulder is taken at 0.166 (FIG. 3: 0.164), where FIG. 7 has its face, and the two after it as the round into the side; ± 3 px
The window model's drawing (MAG556), the same outside.
What runs in the well's spine slot, which is .155 deep (std.ar15.magwell_length less magwell_box_length). On the photos a line runs down the side 0.097 in ahead of the spine's edge (3eded591002b, y -1.9) and 0.118 (8664c534ce73).
The body above the grip frame: the round of its rear corners, from the shoulder beside the spine into the side0.057 in ± 0.012 in 1.4 mmCorroboratedPhoto: US D681,151 S (Magpul), FIG. 7 rear elevation, on the same sheet, 300 dpi
Photo 0.04 in ± 0.012 in
US D681,151 S (Magpul, 'Firearm magazine with window'), FIG. 2 right side elevation, 300 dpi, harvested
Scale: the side trace's own placement of the figure (magpul-pmag-30-gen-m3.overall_height = 7.5 in over 2599 px: 346.6 px/in; x from its rearmost point). Read by from the shoulder's line at x 0.166 to the next, 0.206, at y -1.6; ± 3 px
The window model's drawing (MAG556), the same outside.
Photo 0.057 in ± 0.012 in used
US D681,151 S (Magpul), FIG. 7 rear elevation, on the same sheet, 300 dpi, harvested
Scale: magpul-pmag-30-gen-m3.overall_height = 7.5 in over the figure's 2437 px (rows 467 to 2907, less a line's weight): 324.9 px/in; across from the figure's own middle column. Read by across at y -1.6: the line at 0.399 in from the middle to the silhouette at 0.456; ± 3 px
The window model's drawing (MAG556), the same outside.
The elevation that looks along the corner; the side view's second line may be the round's edge or its tangent. Within the two readings' ±.
The body above the grip frame: how far behind the front face its sides begin to lean in0.602 in ± 0.012 in 15.3 mmProvisionalPhoto: US D681,151 S (Magpul, 'Firearm magazine with window'), FIG. 2 right side elevation, 300 dpi
Photo 0.602 in ± 0.012 in used
US D681,151 S (Magpul, 'Firearm magazine with window'), FIG. 2 right side elevation, 300 dpi, harvested
Scale: the side trace's own placement of the figure (magpul-pmag-30-gen-m3.overall_height = 7.5 in over 2599 px: 346.6 px/in; x from its rearmost point). Read by across the plain side at y -1.2 and -0.55: the line at x 1.989 and 1.995, the front edge at 2.591; ± 3 px
The window model's drawing (MAG556), the same outside.
The upper body narrows toward its front face: each side leans in from this far back to nose_shoulder_width, then rounds into a front face nose_front_width wide (nose_round_depth). On MAG557: Primary Arms' view of the front (53b35012a3a4) has the lean as a facet between the side and the front, with the two ribs standing out of it; on its photo of the right side (8664c534ce73) each rib's sloped upper face is lit, a wedge from 2.14 in to the front that is 0.055 in high at the front, which at guide_rib_top_angle is a lean of 0.10 in there (the drawing's: 0.107). No line marks where the lean begins on either photo (it runs out to nothing).
The body above the grip frame: how far behind the front face the lean ends and the round into the front begins0.068 in ± 0.01 in 1.7 mmProvisionalPhoto: US D681,151 S (Magpul, 'Firearm magazine with window'), FIG. 2 right side elevation, 300 dpi
Photo 0.068 in ± 0.01 in used
US D681,151 S (Magpul, 'Firearm magazine with window'), FIG. 2 right side elevation, 300 dpi, harvested
Scale: the side trace's own placement of the figure (magpul-pmag-30-gen-m3.overall_height = 7.5 in over 2599 px: 346.6 px/in; x from its rearmost point). Read by the broken line at x 2.522 and 2.524, the front edge at 2.591; ± 3 px
The window model's drawing (MAG556), the same outside.
The body above the grip frame: its width where the lean ends0.7 in ± 0.012 in 17.8 mmProvisionalPhoto: US D681,151 S (Magpul), FIG. 6 front elevation, 300 dpi
Photo 0.7 in ± 0.012 in used
US D681,151 S (Magpul), FIG. 6 front elevation, 300 dpi, harvested
Scale: magpul-pmag-30-gen-m3.overall_height = 7.5 in over the figure's 2437 px (rows 467 to 2907, less a line's weight): 324.9 px/in; across from the figure's own middle column. Read by across at y -1.2 (a band 0.4 in high): the lines at 0.350 in each side of the middle (columns 900.7 and 673.2); ± 2 px each
The window model's drawing (MAG556), the same outside.
The body above the grip frame: the flat of its front face0.526 in ± 0.012 in 13.4 mmProvisionalPhoto: US D681,151 S (Magpul), FIG. 6 front elevation, 300 dpi
Photo 0.526 in ± 0.012 in used
US D681,151 S (Magpul), FIG. 6 front elevation, 300 dpi, harvested
Scale: magpul-pmag-30-gen-m3.overall_height = 7.5 in over the figure's 2437 px (rows 467 to 2907, less a line's weight): 324.9 px/in; across from the figure's own middle column. Read by the same band: the lines at 0.265 and 0.262 in from the middle (columns 873.2 and 701.7); ± 2 px each
The window model's drawing (MAG556), the same outside.
The two ribs on the upper body's front: how steeply each one's upper face rises as it goes in from the side29° ± 3°ProvisionalPhoto: US D681,151 S (Magpul), FIG. 6 front elevation, 300 dpi
Photo 29 deg ± 3 deg used
US D681,151 S (Magpul), FIG. 6 front elevation, 300 dpi, harvested
Scale: magpul-pmag-30-gen-m3.overall_height = 7.5 in over the figure's 2437 px (rows 467 to 2907, less a line's weight): 324.9 px/in; across from the figure's own middle column. Read by the upper rib's upper face on the figure's left: from (0.445, -0.480) on the side to (0.255, -0.375) on the front face's edge, 0.105 up over 0.190 in; ± 3 px at each end
The window model's drawing (MAG556), the same outside.
Each rib keeps the side's own width to the front face where the body leans in under it: a flat face flush with the side, a level lower face, and an upper face that rises toward the middle, so that from the side it shows as a wedge above the flat one, growing toward the front (profiles.left, guide_ribs: where the two are on this magazine).
Hang below the magwell when seatedNo value yetMissingNo source yet
Onboarding checklist: Derived: overall_height minus the insertion depth, which is fixed by the mag-catch interface. A check on the seat since M3 (the lower's magazine_seat places magazines).
Length as the manufacturer states it (reference points undefined)7.5 in ± 0.05 in 190.5 mmConfirmedPublished: Magpul, PMAG 30 AR/M4 GEN M3 (MAG557), specifications, the maker, read Oct 2, 2026
Published “Length, max: 7.5 in.” used
Magpul, PMAG 30 AR/M4 GEN M3 (MAG557), specifications, the maker, read Oct 2, 2026 the page, harvested Oct 2, 2026
Capacity30ConfirmedPublished: Magpul, PMAG 30 AR/M4 GEN M3 (MAG557), specifications, the maker, read Oct 2, 2026
Published “Capacity: 30 rds” used
Magpul, PMAG 30 AR/M4 GEN M3 (MAG557), specifications, the maker, read Oct 2, 2026 the page, harvested Oct 2, 2026
Width (side to side) of the body0.997 in ± 0.03 in 25.3 mmProvisionalPhoto: US D681,151 S (Magpul), FIG. 6 front elevation, 300 dpi
Photo 0.997 in ± 0.03 in used
US D681,151 S (Magpul), FIG. 6 front elevation, 300 dpi, harvested
Scale: scale from magpul-pmag-30-gen-m3.overall_height = 7.5 in (y-extent 2437 px → 324.9 px/in). Read by width in y [-4.5, -1.5] of the traced outline (tools/trace.py); the body's width over its middle, below the top's flare and above the floorplate
Magpul gives none. From the patent's front elevation scaled by the height: the body below its top, where the ribs stand out a little; the patent is drawn for the window model (MAG556), the same outside.
The over-travel stop on the spine: half the width of its rear face where it is flat, before its corners round off0.304 in ± 0.012 in 7.7 mmProvisionalPhoto: US D681,151 S (Magpul), sheet 4: FIG. 4 top plan and FIG. 5 bottom plan, 300 dpi
Photo 0.304 in ± 0.012 in used
US D681,151 S (Magpul), sheet 4: FIG. 4 top plan and FIG. 5 bottom plan, 300 dpi, harvested
Scale: the sheet's own scale: its two plans' widest rows (FIG. 4 row 1494, 431 px; FIG. 5 row 1490, 430 px: the floorplate) over the front elevation's floorplate width (profiles.front, 2 x 0.586 in): 367.3 px/in, ± 1% (FIG. 4's length, rows 1039.5 to 2295 over the side outline's 3.443 in, reads 0.7% smaller); across from each figure's own middle (FIG. 4 column 847.5, FIG. 5 column 1755.5, the frame's outer lines). Read by FIG. 4: the rear edge's line on rows 1039 and 1040 from column 736 to 959 (111.5 px each side of the middle); ± 3 px
The window model's drawing (MAG556), the same outside: Primary Arms' view of MAG557 from the rear quarter (b279a01fae08) shows the same ledge, its corners rounded in plan and its gusset under it (a check, not measured).
Photo 0.294 in ± 0.012 in
US D681,151 S (Magpul), sheet 4: FIG. 4 top plan and FIG. 5 bottom plan, 300 dpi, harvested
Scale: the sheet's own scale: its two plans' widest rows (FIG. 4 row 1494, 431 px; FIG. 5 row 1490, 430 px: the floorplate) over the front elevation's floorplate width (profiles.front, 2 x 0.586 in): 367.3 px/in, ± 1% (FIG. 4's length, rows 1039.5 to 2295 over the side outline's 3.443 in, reads 0.7% smaller); across from each figure's own middle (FIG. 4 column 847.5, FIG. 5 column 1755.5, the frame's outer lines). Read by FIG. 5: the same edge on rows 1039 and 1040 from column 1648 to 1864 (108 px each side); ± 3 px
The window model's drawing (MAG556), the same outside: Primary Arms' view of MAG557 from the rear quarter (b279a01fae08) shows the same ledge, its corners rounded in plan and its gusset under it (a check, not measured).
The view from above, where the ledge's top edge is the outline; the two plans agree within their ±.
The stop is a ledge standing out behind the spine at the grip frame's top, what the magazine stops against under a well: seen from above and below its rear face is flat across the middle, its corners round, and its sides lean out going forward until they meet the frame's top band.
The over-travel stop: how far its sides lean out from the magazine's length, going forward from its rounded corners18.3° ± 1.7°ProvisionalPhoto: US D681,151 S (Magpul), sheet 4: FIG. 4 top plan and FIG. 5 bottom plan, 300 dpi
Photo 18.3 deg ± 1.7 deg used
US D681,151 S (Magpul), sheet 4: FIG. 4 top plan and FIG. 5 bottom plan, 300 dpi, harvested
Scale: the sheet's own scale: its two plans' widest rows (FIG. 4 row 1494, 431 px; FIG. 5 row 1490, 430 px: the floorplate) over the front elevation's floorplate width (profiles.front, 2 x 0.586 in): 367.3 px/in, ± 1% (FIG. 4's length, rows 1039.5 to 2295 over the side outline's 3.443 in, reads 0.7% smaller); across from each figure's own middle (FIG. 4 column 847.5, FIG. 5 column 1755.5, the frame's outer lines). Read by FIG. 4: the outline's outer edge, both sides, on rows 1060, 1080, 1100 and 1108 (20.5 to 68.5 px behind the rear edge): 137.25, 144, 150.25, 153.25 px from the middle: 16 px out over 48 px along (0.33); FIG. 5 the same within a pixel (136, 143, 151 px at 20.5, 35.5, 60.5); ± 1 px a reading
The window model's drawing (MAG556), the same outside: Primary Arms' view of MAG557 from the rear quarter (b279a01fae08) shows the same ledge, its corners rounded in plan and its gusset under it (a check, not measured).
Each side is straight from where its corner's round ends to where it meets the frame's top band (stop_length), out to stop_half_width there.
The over-travel stop: half its widest, where its sides meet the frame's top band0.431 in ± 0.008 in 10.9 mmCorroboratedPhoto: US D681,151 S (Magpul), FIG. 7 rear elevation, on the same sheet, 300 dpi
Photo 0.431 in ± 0.008 in used
US D681,151 S (Magpul), FIG. 7 rear elevation, on the same sheet, 300 dpi, harvested
Scale: magpul-pmag-30-gen-m3.overall_height = 7.5 in over the figure's 2437 px (rows 467 to 2907, less a line's weight): 324.9 px/in; across from the figure's own middle column (1765, between the spine's two lines and the gusset's). Read by FIG. 7: the ledge's two end lines, columns 1625.0 and 1905.0 on rows 1460 to 1505 (140 px each side of the middle); ± 2 px
The window model's drawing (MAG556), the same outside: Primary Arms' view of MAG557 from the rear quarter (b279a01fae08) shows the same ledge, its corners rounded in plan and its gusset under it (a check, not measured).
Photo 0.425 in ± 0.012 in
US D681,151 S (Magpul), sheet 4: FIG. 4 top plan and FIG. 5 bottom plan, 300 dpi, harvested
Scale: the sheet's own scale: its two plans' widest rows (FIG. 4 row 1494, 431 px; FIG. 5 row 1490, 430 px: the floorplate) over the front elevation's floorplate width (profiles.front, 2 x 0.586 in): 367.3 px/in, ± 1% (FIG. 4's length, rows 1039.5 to 2295 over the side outline's 3.443 in, reads 0.7% smaller); across from each figure's own middle (FIG. 4 column 847.5, FIG. 5 column 1755.5, the frame's outer lines). Read by FIG. 4: the side's line where it meets the band's (row 1115, columns 690 to 695: 156 px from the middle); ± 3 px
The window model's drawing (MAG556), the same outside: Primary Arms' view of MAG557 from the rear quarter (b279a01fae08) shows the same ledge, its corners rounded in plan and its gusset under it (a check, not measured).
The view that looks across the ledge's widest; the plan agrees within the two readings' ±.
The rear elevation sees it as the ledge's two ends, inside the frame's silhouette (0.485 each side): the stop is narrower than the frame.
The over-travel stop: how far forward of its rear face its sides run before they meet the frame's top band0.206 in ± 0.01 in 5.2 mmProvisionalPhoto: US D681,151 S (Magpul), sheet 4: FIG. 4 top plan and FIG. 5 bottom plan, 300 dpi
Photo 0.206 in ± 0.01 in used
US D681,151 S (Magpul), sheet 4: FIG. 4 top plan and FIG. 5 bottom plan, 300 dpi, harvested
Scale: the sheet's own scale: its two plans' widest rows (FIG. 4 row 1494, 431 px; FIG. 5 row 1490, 430 px: the floorplate) over the front elevation's floorplate width (profiles.front, 2 x 0.586 in): 367.3 px/in, ± 1% (FIG. 4's length, rows 1039.5 to 2295 over the side outline's 3.443 in, reads 0.7% smaller); across from each figure's own middle (FIG. 4 column 847.5, FIG. 5 column 1755.5, the frame's outer lines). Read by FIG. 4: the band's line across the stop's side, rows 1113.5 to 1117 on columns 690 to 705, 75.5 px behind the rear edge (row 1039.5); FIG. 5 the same (rows 1114.5 to 1117.5 on columns 1600 to 1610); ± 3 px
The window model's drawing (MAG556), the same outside: Primary Arms' view of MAG557 from the rear quarter (b279a01fae08) shows the same ledge, its corners rounded in plan and its gusset under it (a check, not measured).
The over-travel stop: how far down its rear face comes in the middle, under the ledge's top where it meets the spine0.178 in ± 0.01 in 4.5 mmProvisionalPhoto: US D681,151 S (Magpul), FIG. 7 rear elevation, on the same sheet, 300 dpi
Photo 0.178 in ± 0.01 in used
US D681,151 S (Magpul), FIG. 7 rear elevation, on the same sheet, 300 dpi, harvested
Scale: magpul-pmag-30-gen-m3.overall_height = 7.5 in over the figure's 2437 px (rows 467 to 2907, less a line's weight): 324.9 px/in; across from the figure's own middle column (1765, between the spine's two lines and the gusset's). Read by FIG. 7: the face's lower edge, the middle of its pair of lines, on columns 1700, 1720 (rows 1496.5/1503, 1502.5), and the gusset's top at 1500.5 on column 1765, against the ledge's top edge at row 1442 (columns 1640 and 1660); ± 3 px
The window model's drawing (MAG556), the same outside: Primary Arms' view of MAG557 from the rear quarter (b279a01fae08) shows the same ledge, its corners rounded in plan and its gusset under it (a check, not measured).
Each of the stop's depths is read under the ledge's top edge as the rear elevation draws it, which is its highest, where it meets the spine's face (FIG. 7's row 1442 is 3.00 in under the lips on the figure's own scale; the side outline's top crosses the spine's face at 2.998, falling to 3.04 at the tip as the side elevation draws the ledge rounded over). The rear elevation draws the rear face deepest across the middle (to where the gusset begins under it), shallower toward its ends: under the face, the stop is hollow either side of the gusset (stop_bay_half_width) and its outer parts slope up to the face's lower edge (stop_wing_*).
The over-travel stop: how far out from the middle its rear face keeps its middle depth0.262 in ± 0.02 in 6.7 mmProvisionalPhoto: US D681,151 S (Magpul), FIG. 7 rear elevation, on the same sheet, 300 dpi
Photo 0.262 in ± 0.02 in used
US D681,151 S (Magpul), FIG. 7 rear elevation, on the same sheet, 300 dpi, harvested
Scale: magpul-pmag-30-gen-m3.overall_height = 7.5 in over the figure's 2437 px (rows 467 to 2907, less a line's weight): 324.9 px/in; across from the figure's own middle column (1765, between the spine's two lines and the gusset's). Read by FIG. 7: the face's lower edge at its middle depth out to column 1680 (rows 1495.5/1502.5); at column 1660 it has risen to rows 1485/1493
The window model's drawing (MAG556), the same outside: Primary Arms' view of MAG557 from the rear quarter (b279a01fae08) shows the same ledge, its corners rounded in plan and its gusset under it (a check, not measured).
The over-travel stop: how far down its rear face comes toward its ends0.103 in ± 0.012 in 2.6 mmProvisionalPhoto: US D681,151 S (Magpul), FIG. 7 rear elevation, on the same sheet, 300 dpi
Photo 0.103 in ± 0.012 in used
US D681,151 S (Magpul), FIG. 7 rear elevation, on the same sheet, 300 dpi, harvested
Scale: magpul-pmag-30-gen-m3.overall_height = 7.5 in over the figure's 2437 px (rows 467 to 2907, less a line's weight): 324.9 px/in; across from the figure's own middle column (1765, between the spine's two lines and the gusset's). Read by FIG. 7: the face's lower edge on column 1640 (rows 1471.5/1479.5), 33.5 px under the top edge; at column 1660, between the two (rows 1485/1493: 0.145 in), as a straight line between this and the middle depth puts it; ± 3 px
The window model's drawing (MAG556), the same outside: Primary Arms' view of MAG557 from the rear quarter (b279a01fae08) shows the same ledge, its corners rounded in plan and its gusset under it (a check, not measured).
The over-travel stop: how far out from the middle the rear face's lower edge reaches stop_lip_depth_end0.385 in ± 0.01 in 9.8 mmProvisionalPhoto: US D681,151 S (Magpul), FIG. 7 rear elevation, on the same sheet, 300 dpi
Photo 0.385 in ± 0.01 in used
US D681,151 S (Magpul), FIG. 7 rear elevation, on the same sheet, 300 dpi, harvested
Scale: magpul-pmag-30-gen-m3.overall_height = 7.5 in over the figure's 2437 px (rows 467 to 2907, less a line's weight): 324.9 px/in; across from the figure's own middle column (1765, between the spine's two lines and the gusset's). Read by FIG. 7: column 1640, where stop_lip_depth_end is read (125 px from the middle); outward of it the edge turns down into the ledge's rounded end
The window model's drawing (MAG556), the same outside: Primary Arms' view of MAG557 from the rear quarter (b279a01fae08) shows the same ledge, its corners rounded in plan and its gusset under it (a check, not measured).
The over-travel stop: under its outer parts, how far below its top the sloping underside comes at stop_wing_half_width0.156 in ± 0.012 in 4 mmProvisionalPhoto: US D681,151 S (Magpul), FIG. 7 rear elevation, on the same sheet, 300 dpi
Photo 0.156 in ± 0.012 in used
US D681,151 S (Magpul), FIG. 7 rear elevation, on the same sheet, 300 dpi, harvested
Scale: magpul-pmag-30-gen-m3.overall_height = 7.5 in over the figure's 2437 px (rows 467 to 2907, less a line's weight): 324.9 px/in; across from the figure's own middle column (1765, between the spine's two lines and the gusset's). Read by FIG. 7: column 1640, the lower edge's pair of lines at rows 1487.5 and 1498 (their middle 1492.75), 50.75 px under the top edge; ± 3 px
The window model's drawing (MAG556), the same outside: Primary Arms' view of MAG557 from the rear quarter (b279a01fae08) shows the same ledge, its corners rounded in plan and its gusset under it (a check, not measured).
The rear elevation draws a second edge under each end of the face, coming down from near the ledge's end to the spine's edge where the frame's top band ends: the underside of the ledge's outer parts, which slopes down from the face's lower edge going forward (the side elevation, FIG. 2, draws it as a sloping face under the ledge's end). Drawn as ruled from the face's lower edge at the rear to a straight edge at the spine's face, from this point down to the spine's edge at the top of the first row: FIG. 7's edge at column 1660 reads 0.205 in under the top where that line has 0.178, the difference being where the figure and the side outline put the band's lower edge (FIG. 7 0.24 to 0.27 under the stop's top, the side elevation and the model 0.21).
The over-travel stop: how far out from the middle stop_wing_depth is read0.385 in ± 0.01 in 9.8 mmProvisionalPhoto: US D681,151 S (Magpul), FIG. 7 rear elevation, on the same sheet, 300 dpi
Photo 0.385 in ± 0.01 in used
US D681,151 S (Magpul), FIG. 7 rear elevation, on the same sheet, 300 dpi, harvested
Scale: magpul-pmag-30-gen-m3.overall_height = 7.5 in over the figure's 2437 px (rows 467 to 2907, less a line's weight): 324.9 px/in; across from the figure's own middle column (1765, between the spine's two lines and the gusset's). Read by FIG. 7: column 1640 (125 px from the middle)
The window model's drawing (MAG556), the same outside: Primary Arms' view of MAG557 from the rear quarter (b279a01fae08) shows the same ledge, its corners rounded in plan and its gusset under it (a check, not measured).
The over-travel stop: under it, how far out from the middle the hollow either side of the gusset reaches at the rear face0.271 in ± 0.012 in 6.9 mmProvisionalPhoto: US D681,151 S (Magpul), sheet 4: FIG. 4 top plan and FIG. 5 bottom plan, 300 dpi
Photo 0.271 in ± 0.012 in used
US D681,151 S (Magpul), sheet 4: FIG. 4 top plan and FIG. 5 bottom plan, 300 dpi, harvested
Scale: the sheet's own scale: its two plans' widest rows (FIG. 4 row 1494, 431 px; FIG. 5 row 1490, 430 px: the floorplate) over the front elevation's floorplate width (profiles.front, 2 x 0.586 in): 367.3 px/in, ± 1% (FIG. 4's length, rows 1039.5 to 2295 over the side outline's 3.443 in, reads 0.7% smaller); across from each figure's own middle (FIG. 4 column 847.5, FIG. 5 column 1755.5, the frame's outer lines). Read by FIG. 5: the wall's pair of lines, both sides, on rows 1046 to 1076 (6.5 to 36.5 px ahead of the rear edge): their middle 96.6, 95.9, 92.6, 89.0, 86.1, 84.0 px from the middle; a line through them, 99.5 - 0.42 x px, at the rear edge; ± 3 px
The window model's drawing (MAG556), the same outside: Primary Arms' view of MAG557 from the rear quarter (b279a01fae08) shows the same ledge, its corners rounded in plan and its gusset under it (a check, not measured).
FIG. 5 (from below) draws each hollow's outer wall as a straight line from the rear face forward and in to the spine's edge at the spine's face (it reads 0.221 in, the spine's half width, 0.12 in ahead of the rear face); FIG. 8 draws the two hollows either side of the gusset. The hollow's roof is the face's lower edge in the middle (stop_lip_depth_middle): FIG. 5 has the face's lower edge 0.01 in ahead of its upper one there, and nothing else across the hollow.
What it goes with
By the way it mounts, and the figures each part on file states: a part whose figures say it doesn't fit is left out, and one whose fit can't be checked from what is published is marked. A check is against published figures, not a guarantee.
AR-15 magazine well
- Lower receivers
- Aero Precision M4E1 complete lower, A2 grip and M4 stock, Aero Precision M4E1 Stripped Lower Receiver, Battle Arms Development Workhorse stripped lower, BCM MK2 AR-15 Lower Receiver, Bear Creek Arsenal BC-15 Multi Caliber, Lower Receiver, Black Anodized, Geissele Automatics Super Duty AR-15 Lower Receiver - Stripped Lower, Palmetto State Armory AR-15 "Stealth" Stripped Lower Receiver
Prices on file
Each seller's latest reading of its own page: before tax and shipping, and not a quote. The pages are read again every night.
- Primary Arms $12.88 Black Nov 21, 2026, in stock that day
- Midwest Gun Works $14.20 Black Nov 21, 2026, in stock that day
- Midwest Gun Works $14.20 ODG Nov 21, 2026, in stock that day
- Midwest Gun Works $14.20 Medium Coyote Tan Nov 21, 2026, in stock that day
- Midwest Gun Works $14.20 Modified Coyote Brown Nov 21, 2026, in stock that day
- Mile High Shooting Accessories $15.15 Black Nov 21, 2026, in stock that day
- Magpul $15.95 Nov 21, 2026, stock not said