Grip
BCM Grip Mod 4
BCM's newest reduced-angle grip ("An update to the classic A1 and A2 design ... a new form factor with a reduced angle and a new ultra-tactile grip texture"): a high beavertail, a tang that reaches forward to the trigger guard, coarse ribs across its front strap, and an open bottom where the Mod 3 has a trap door ("Open bottom to minimize weight"). Its straps lean 17.4 degrees installed, less than the Mod 3's 20.

- Weight
- 2.48 oz ± 0.5 oz Provisionalworked out: The model's polymer volume, 3.767 cubic inches (pipeline/blender/bcm_grip_mod_4.py's manifest, volume_in3), times std.density.polymer (18.68 g, 0.659 oz to the cubic inch: a polyamide's; BCM says "high quality impact resistant polymers" and names no grade): 2.48 oz. The ± is the open bottom's assumed wall (± 0.05 in) and depth (± 0.4 in), about 0.3 and 0.2 oz, and a glass fill, which no page rules out (up to 0.2 g/ml heavier: 0.4 oz). The screw and washer BCM includes aren't drawn and aren't in it. app/tests/bcm-grip-mod-4.test.ts holds the model's volume to it.
- Lowest price
- $17.95 at BCM, read Nov 21, 2026 (Black)
- Maker's number
- BCM-GFG-MOD-4-BLK
- Colours
- Black, Flat Dark Earth
- Drawn as
- modelled
- Maker's page
- bravocompanyusa.com
In “Drop-in 16 in, Stealth Gray on BCM's MK2 lower”, a build on the start page, as it is.
Its figures
Every figure the site draws and checks it by, with where it came from. Open one for each source's reading, and why one is used where they differ.
The grip's lowest point (its toe) below the takedown pin, installed5.248 in ± 0.03 in 133.3 mmProvisionalPhoto: Primary Arms LRG-RMS-NO-STOCK_01: BCM's MK2 lower without stock, its right side square on white, the Mod 4 grip on it, 2200 x 1467
Photo 5.248 in ± 0.03 in used
Primary Arms LRG-RMS-NO-STOCK_01: BCM's MK2 lower without stock, its right side square on white, the Mod 4 grip on it, 2200 x 1467, harvested
Scale: the lower's own pins and holes at the Army drawing's places (std.ar15.pin_spacing, selector, trigger and hammer pins, the guard's two holes: 134.1 px/in, the worst miss 0.045 in; the lower's owner's frame). Read by the grip's silhouette below the guard (luminance < 200, inside [940, 830, 1300, 1260], the largest piece, closed ×2): its lowest point, −5.248 (tools/trace.py, spec installed). ± is the frame's 0.5% over 5.2 in and the edge's 2 px.
Read in a frame of the lower's pins, where the grip stands against the white below the trigger guard. The frame is set at the receiver's right face (the pins' heads and the drawing's holes): the grip's silhouette is its own widest, at about the same depth from the lens, so it reads at about the frame's scale.
Grip bottom below the receiver's underside where the grip bears4.179 in ± 0.032 in 106.1 mmProvisionalWorked out: {.toe_below_pin} + {std.ar15.deck_y} - {std.ar15.grip_seat_below_deck}
Worked out 4.179 in used
{.toe_below_pin} + {std.ar15.deck_y} - {std.ar15.grip_seat_below_deck}, harvested
The toe read in the pin-framed photo of the grip installed, less the seat's depth below the pin line by the Army drawing (1.318 below the deck, which is .2485 above the pin).
What the side photo is scaled by: from the grip's flat top, which bears on the receiver's underside under the lug (std.ar15.grip_seat_below_deck below the deck, the deck std.ar15.deck_y above the pin), to its toe.
Grip angle (the straps' lean from vertical, installed)17.4° ± 0.5°ConflictPhoto: Primary Arms BCM-GFG-MOD-4-BLK_01: the black grip on white, straight right side, 2200 x 1467
Photo 17.4 deg ± 1.6 deg
Primary Arms LRG-RMS-NO-STOCK_01: BCM's MK2 lower without stock, its right side square on white, the Mod 4 grip on it, 2200 x 1467, harvested
Scale: none needed for an angle: the frame of the lower's pins sets the level. Read by a straight line through the grip's silhouette along each strap, 2.9 to 4.3 in below the pin: the back strap 19.35 ± 1.1 degrees from the vertical (1.48 in of it, rms 0.009), the front strap 15.41 ± 2.8 (0.54 in of it between its ribs, rms 0.007); their mean. ± is half the two straps' difference with the shorter run's own (tools/trace.py line_lean, spec installed).
Photo 17.4 deg ± 0.5 deg used
Primary Arms BCM-GFG-MOD-4-BLK_01: the black grip on white, straight right side, 2200 x 1467, harvested
Scale: none needed: an angle within one outline. Read by the side outline (luminance < 200) turned so that its straps' mean lean in the band 0.45-0.85 of its height is 17.4 (rear 19.4, front 15.4): its flat top, from its rear end to the block's front corner (1.08 in, 11 outline points), then lies level to within 0.01 in, 0.3 degrees: the grip's flat top level is this lean. ± is that and the edges' 1.5 px over the band.
Photo 15.6 deg ± 1.1 deg
Primary Arms LRG-RMS-NO-STOCK_01: BCM's MK2 lower without stock, its right side square on white, the Mod 4 grip on it, 2200 x 1467, harvested
Scale: the side outline at its own scale (the drop it is scaled by is read in this photo). Read by the side outline fitted into the grip's silhouette below the guard (2.6 in of it, the straps and the foot; 1150 edge points, rms 0.046 in), turned and moved, scale fixed: it turns 2.0 degrees more upright; the fitted outline's straps lean 17.6 and 13.7 (tools/trace.py registered_lean, spec installed-fit). Free in scale it fits at 0.970 and turns 2.6 degrees.
Kept in view: the fit sees only the lower half of the grip, whose foot (seen from above its base: the open bottom's rim shows) it weighs as much as the straps.
Installed, the flat top lies on the receiver's level underside, so the straps lean as they do from that face: an angle inside one outline, the photo the side outline is traced from. The straight lines along the two straps in the pin-framed photo of the grip installed read the same (17.4). The fit of the outline's lower half into that photo turns it 2 degrees further (15.6 ± 1.1): it weighs the foot, seen from above, as much as the straps, and its rms (0.046 in) is four times the straps' lines'.
flat-top-pa and installed-fit differ by 1.8° beyond what each states it is good to.
The mean of the back and front straps' lean (the band 0.45 to 0.85 of the outline's height) with the flat top, which bears on the receiver's underside, level. BCM gives no figure: "Reduced angle for improved ergonomics and trigger control". The back strap leans about 19.4, the front strap 15.4.
Overall height in the grip frame (the beavertail's top to the toe)4.846 in ± 0.05 in 123.1 mmProvisionalPhoto: Primary Arms BCM-GFG-MOD-4-BLK_01: the black grip on white, straight right side, 2200 x 1467
Photo 4.846 in ± 0.05 in used
Primary Arms BCM-GFG-MOD-4-BLK_01: the black grip on white, straight right side, 2200 x 1467, harvested
Scale: scale from bcm-grip-mod-4.bottom_below_lower_underside = 4.179 in (y from the origin to the far edge 1090 px → 260.9 px/in). Read by height of the traced outline (tools/trace.py); the traced outline's height, the beavertail's top to the toe
Top block's front face, ahead of the flat top's rear end1.265 in ± 0.015 in 32.1 mmProvisionalPhoto: Primary Arms BCM-GFG-MOD-4-BLK_01: the black grip on white, straight right side, 2200 x 1467
Photo 1.265 in ± 0.015 in used
Primary Arms BCM-GFG-MOD-4-BLK_01: the black grip on white, straight right side, 2200 x 1467, harvested
Scale: scale from bcm-grip-mod-4.bottom_below_lower_underside = 4.179 in (y from the origin to the far edge 1090 px → 260.9 px/in). Read by x_max in y [-0.85, -0.25] of the traced outline (tools/trace.py); the top block's front face ahead of the flat top's rear end, between the corner above it and the tang below
Seat, X: where the grip's frame origin (its flat top's rear end) sits ahead of the takedown pin, installed-0.09 in ± 0.019 in -2.3 mmConflictWorked out: {std.ar15.receiver_rear_x} + {std.ar15.grip_lug_front_from_rear_face} - {.block_front_x}
Worked out -0.09 in used
{std.ar15.receiver_rear_x} + {std.ar15.grip_lug_front_from_rear_face} - {.block_front_x}, harvested
The block's front face (block_front_x, on the traced side) at the ears' rear face.
Photo -0.24 in ± 0.05 in
Primary Arms LRG-RMS-NO-STOCK_01: BCM's MK2 lower without stock, its right side square on white, the Mod 4 grip on it, 2200 x 1467, harvested
Scale: the lower's pins at the Army drawing's places (134.1 px/in). Read by where the side outline's origin lands when its lower half is fitted into the grip's silhouette below the guard (scale fixed; rms 0.046 in): x -0.240, y -1.052 (the seat by the drawing is -1.0695). The fit turns the outline 2.0 degrees, which moves an origin 4 in above the fitted part by 0.14 in (tools/trace.py registered_x, spec installed-fit).
Kept in view: a fit 4 in below the seat it reads, turned by the angle the flat top says it isn't.
The block's front face bears on the ears' rear face, where the Army drawing ends the lug: the interface seats it. The fit's origin is 4 in above what it fits, and it turns the outline 2 degrees off its flat top: at the flat top's angle the fit's own rotation, 2.0 degrees about the foot, accounts for 0.14 of its 0.15 in.
interface and installed-fit differ by 0.15 in beyond what each states it is good to.
A grip's own figure on the standard AR-15 grip mount. Seated by its interface, as BCM's Mod 3 is: the top block's front face against the rear face of the trigger guard's ears, where the Army drawing ends the lug (2.300 from the receiver's rear face, 1.175 ahead of the takedown pin).
Thickness (side to side), across the hand grip's body1.239 in ± 0.061 in 31.5 mmProvisionalPhoto: BCM's BCM-MOD-4-GRIP-BLK-2: the black grip from ahead, its front strap straight on, from a little above, cut out on white, 1000 x 1000
Photo 1.239 in ± 0.061 in used
BCM's BCM-MOD-4-GRIP-BLK-2: the black grip from ahead, its front strap straight on, from a little above, cut out on white, 1000 x 1000, harvested
Scale: scale from bcm-grip-mod-4.top_block_width = 0.88 in (median width over 0.08–0.19 of the height from the top, 119–123 px 119 px → 135.2 px/in). Read by median row width in y [-3.6, -1.6] (1.214–1.272) of the traced outline (tools/trace.py); the median row width of the hand grip's body (rows 388 to 663 of 1000), at the scale the block's two walls give the top (rows 230 to 300, 119 to 122 px across for 0.88 in)
Foot (the flare at the base), across: the widest the grip is, side to side1.279 in ± 0.062 in 32.5 mmProvisionalPhoto: BCM's BCM-MOD-4-GRIP-BLK-2: the black grip from ahead, its front strap straight on, from a little above, cut out on white, 1000 x 1000
Photo 1.279 in ± 0.062 in used
BCM's BCM-MOD-4-GRIP-BLK-2: the black grip from ahead, its front strap straight on, from a little above, cut out on white, 1000 x 1000, harvested
Scale: scale from bcm-grip-mod-4.top_block_width = 0.88 in (median width over 0.08–0.19 of the height from the top, 119–123 px 119 px → 135.2 px/in). Read by width of the traced outline (tools/trace.py); the outline's widest row, at the foot's flare, at the scale the block's walls give the top
Top block (the two walls that sit under the receiver), across0.88 in ± 0.04 in 22.4 mmProvisionalPhoto: Primary Arms LRG-RMS-NO-STOCK_01: the MK2 lower with this grip, right side) and d872250eaa9b (its blem, from ahead of the right side and above
Photo 0.88 in ± 0.04 in used
Primary Arms LRG-RMS-NO-STOCK_01: the MK2 lower with this grip, right side) and d872250eaa9b (its blem, from ahead of the right side and above, harvested
Scale: the receiver's own width where the grip meets it: the standard's 0.88 in body (std.ar15.lower_body_width). Read by the block's side face runs on into the receiver's with no step at the seam, on the side the photos show: taken as the receiver's width. ± is a step of 0.02 in a side, which wouldn't show at this size.
No page gives it and no photo is square to it. The army's A2 grip is .885 across its top (aero-m4e1-lower.grip_body_width, drawing 9349127).
The slot in the top that goes over the receiver's lug, across0.394 in ± 0.03 in 10 mmProvisionalPhoto: BCM's BCM-MOD-4-GRIP-BLK-2: the black grip from ahead, from a little above, 1000 x 1000
Photo 0.394 in ± 0.03 in used
BCM's BCM-MOD-4-GRIP-BLK-2: the black grip from ahead, from a little above, 1000 x 1000, harvested
Scale: the block's own width across the same face (bcm-grip-mod-4.top_block_width, 0.88 ± 0.04). Read by on a 4x gridded crop at row 330 (the screw's hole), the walls' outer edges at columns 442.5 and 562.5 and the slot's walls at 477 and 530.75: 53.75 px of 120, 0.448 of the block. ± is 1.5 px on each of the slot's edges and the block's width.
Wider than the standard lug's .375 (std.ar15.grip_lug_width) by 0.01 a side: the slot goes over the lug.
Read on BCM's photo of the grip from ahead, which looks down the slot (its floor lit, the screw's hole in it) between the block's two walls: the walls' inner faces and outer faces are four lines across one view, so their spacing along a row needs no scale but the walls' own width.
Front strap's ribs: how far back from the strap's edge they run, in the side view0.2 in ± 0.03 in 5.1 mmProvisionalPhoto: Primary Arms BCM-GFG-MOD-4-BLK_01: the black grip on white, straight right side, 2200 x 1467
Photo 0.2 in ± 0.03 in used
Primary Arms BCM-GFG-MOD-4-BLK_01: the black grip on white, straight right side, 2200 x 1467, harvested
Scale: the 4.179 in drop (bcm-grip-mod-4.bottom_below_lower_underside): 260.9 px/in. Read by read on a gridded 3x crop at rows 850 to 1100 (columns 1100 to 1400): the ribs' crests at the outline's edge and their rear ends (where their shadows stop, before the smooth band at the texture panel's border), 50 to 53 px apart. ± is 8 px.
Counted on the stored side outline turned upright (its front edge's crests, each the highest within a rib's pitch either way): 19 ribs from 1.41 to 3.32 in down the strap, 0.106 in apart on average (0.08 to 0.13 at the outline's 0.006 in simplification); on the photo they stand about 0.035 in out of the strap (8 to 10 px). From ahead (BCM's BLK-2) they run across the whole front strap between the two texture panels.
The open bottom's rim: the wall round the opening at the base, across0.12 in ± 0.05 in 3 mmProvisionalWorked out: An assumption for the drawing, not a reading: Primary Arms' views from below (d41f5fa6a14e, f669645dcd74) show the rim at 25 to 80 px of a base 460 to 700 px across, at an angle no figure on file sets; the ± covers a rim from a fourteenth to a sixth of an inch.
Worked out 0.12 in ± 0.05 in used
An assumption for the drawing, not a reading: Primary Arms' views from below (d41f5fa6a14e, f669645dcd74) show the rim at 25 to 80 px of a base 460 to 700 px across, at an angle no figure on file sets; the ± covers a rim from a fourteenth to a sixth of an inch., harvested
BCM: "Open bottom to minimize weight". Primary Arms' two views from below (black and FDE) show the base as a rim round a rounded opening, the rim about a tenth of the base's span; neither is square to the base, so its width is drawn as assumed, not read.
How far up the open bottom's hollow reaches: its top, below the grip's flat top1.3 in ± 0.4 in 33 mmProvisionalWorked out: An assumption for the drawing, not a reading: no view on file shows the hollow's top. Taken under the slot's floor (the standard lug's depth, 0.93 in below the top, std.ar15.grip_lug_depth) with a wall under it for the screw's head to bear on; the ± runs from just under that floor to half way down the grip.
Worked out 1.3 in ± 0.4 in used
An assumption for the drawing, not a reading: no view on file shows the hollow's top. Taken under the slot's floor (the standard lug's depth, 0.93 in below the top, std.ar15.grip_lug_depth) with a wall under it for the screw's head to bear on; the ± runs from just under that floor to half way down the grip., harvested
No view shows the hollow's top: the views from below see dark inside it. The screw goes down through the slot's floor (the hole in BCM's view from ahead) and its head is reached through the hollow.
What it goes with
By the way it mounts, and the figures each part on file states: a part whose figures say it doesn't fit is left out, and one whose fit can't be checked from what is published is marked. A check is against published figures, not a guarantee.
AR-15 grip mount
- Lower receivers
- Aero Precision M4E1 complete lower, A2 grip and M4 stock, Aero Precision M4E1 Stripped Lower Receiver, Battle Arms Development Workhorse stripped lower, BCM MK2 AR-15 Lower Receiver, Bear Creek Arsenal BC-15 Multi Caliber, Lower Receiver, Black Anodized, Geissele Automatics Super Duty AR-15 Lower Receiver - Stripped Lower, Palmetto State Armory AR-15 "Stealth" Stripped Lower Receiver
Prices on file
Each seller's latest reading of its own page: before tax and shipping, and not a quote. The pages are read again every night.
- BCM $17.95 Black Nov 21, 2026, in stock that day
- BCM $17.95 Flat Dark Earth Nov 21, 2026, in stock that day
- Primary Arms $17.95 Black Nov 21, 2026, in stock that day
- Primary Arms $17.95 Flat Dark Earth Nov 21, 2026, in stock that day
- KYGUNCO $17.95 Black Nov 21, 2026, in stock that day