Magazine
Magpul PMAG D-60 AR/M4 GEN M3
Magpul's 60-round polymer drum for AR-15/M4 rifles in 5.56 NATO and .223 Remington: a GEN M3 feed tower on a drum 4.1 in across, with a ratcheting loading lever on its front cover and a round-count window and a paint-pen dot matrix on its rear. Its slip-on dust cover comes off before it goes into a rifle and is not drawn.

- Weight
- 20.5 oz ± 0.05 oz Confirmedpublished: Magpul, PMAG D-60 AR/M4 GEN M3 (MAG576), technical specifications, the maker, read Oct 6, 2026
- Lowest price
- $102.99 at KYGUNCO, read Nov 21, 2026
- Made for
- Caliber 5.56x45mm / .223 Remington ... Optimized for use only with 5.56x45 NATO/.223 Remington cartridges. Use with other calibers such as .300 AAC Blackout is not recommended.
- Maker's number
- MAG576
- Colour
- Magpul Black
- Drawn as
- modelled
- Maker's page
- magpul.com
In “Aero 5.56 carbine”, a build on the start page, in place of its Magpul PMAG 30 AR/M4 GEN M3.
Its figures
Every figure the site draws and checks it by, with where it came from. Open one for each source's reading, and why one is used where they differ.
Overall height, feed lips to the drum's lowest point, standing with the drum's two faces upright7.4 in ± 0.05 in 188 mmConfirmedPublished: Magpul, PMAG D-60 AR/M4 GEN M3 (MAG576), technical specifications, the maker, read Oct 6, 2026
Published “Length, max 7.4 in.” used
Magpul, PMAG D-60 AR/M4 GEN M3 (MAG576), technical specifications, the maker, read Oct 6, 2026 the page, harvested Oct 6, 2026
Magpul's 'Length, max', read as the height of the magazine standing as the studio photo from the rear has it, square to the rear cover (9a2a10cb54cb: nothing of the roof or the lever shows over the collar, which a drum hanging nose up under an upright tower would show behind it; its hub's rim reads 0.990 as tall as wide, between square on and the 0.985 of a 10 degree lean, so that doesn't say): the silhouette is 1180 px tall and 654 px wide, 1.804 to 1, and Magpul's 7.4 to 4.1 is 1.805. With the feed tower upright instead (as a magazine well holds it, the drum then nose up by tower_lean) the model is 7.36 in from the lips to its lowest point, inside the figure's last digit. Magpul's design patent draws the same pose (US D765,813 FIG. 2 to 5) but its figure is 1.757 to 1 (FIG. 3: 2132 by 1212 px): its broken-line tower is about 0.2 in shorter than the product's.
Body height below the feed-lip blockNo value yetMissingNo source yet
Onboarding checklist: Side view; overall_height minus the feed-lip block when the block is shared across a product line.
Feed-lip block heightNo value yetMissingNo source yet
Onboarding checklist.
Front to back at the body top2.528 in ± 0.035 in 64.2 mmProvisionalWorked out: {magpul-pmag-30-gen-m3.front_to_back}
Worked out 2.528 in ± 0.035 in used
{magpul-pmag-30-gen-m3.front_to_back}
The feed tower taken as Magpul's GEN M3 magazine's top: on this part's own photo its width (tower_width, 0.875 in) and the ledge under its catch's window (catch_notch_lower_edge) are where the 30-round's are.
Photo 2.48 in ± 0.04 in
US D765,813 S (Magpul, 'Drum magazine for a firearm'), FIG. 4 left side elevation, 300 dpi, harvested
Scale: the drum outline's scale (tools/trace.py): magpul-pmag-d-60.drum_height = 4.487 in over 1454 px, 324.0 px/in, the height handed on from FIG. 3 scaled by magpul-pmag-d-60.stated_width = 4.1 in. Read by the tower's two long edges in broken lines, as a polygon picked on gridded enlargements (± 3 px): 815 px apart along a level line at row 1000, 803 px square to the spine
The patent's broken-line tower (unclaimed, environment): drawn a little small against the product (its width in FIG. 3 reads 0.83 in for the photo's 0.875, its top about 0.2 in short).
The patent draws the tower in broken lines and a little small all round; the GEN M3 figure is a traced one of the same maker's own tower, and the two agree within their ±.
The feed tower's front to back where it stands in the well. No straight side view of the D-60 itself is on file: its tower is Magpul's GEN M3 (the page: 'proven GEN M3 internals'; the name), checked on its own rear photo.
Magazine catch notch (left side), its upper edge below the feed lips' top1.1 in ± 0.05 in 27.9 mmConflictWorked out: {.catch_notch_lower_edge} - {magpul-pmag-30-gen-m3.catch_notch_height}
Worked out 1.1 in ± 0.05 in used
{.catch_notch_lower_edge} - {magpul-pmag-30-gen-m3.catch_notch_height}
This part's own ledge under the window (its photo), less the window's height as Magpul's 30-round GEN M3 has it (0.25 in, the height of the slot a lower's catch comes through): the window itself is in no straight view of the D-60.
Photo 0.815 in ± 0.03 in
US D765,813 S (Magpul, 'Drum magazine for a firearm'), FIG. 4 left side elevation, 300 dpi, harvested
Scale: the drum outline's scale (tools/trace.py): magpul-pmag-d-60.drum_height = 4.487 in over 1454 px, 324.0 px/in, the height handed on from FIG. 3 scaled by magpul-pmag-d-60.stated_width = 4.1 in. Read by the upper edge of the rounded rectangle the patent's broken lines draw on the tower's left side, its corners picked at (1379, 800) and (1500, 779) px, below the drawn tower's top at (1598, 495), along the tower (turned 9.9°): 264 px
The patent's broken-line tower (unclaimed): its top is drawn about 0.2 in lower than the product's (the whole figure is 1.757 as tall as wide, the product's photo 1.804), so everything on it reads that much nearer the top.
The product's own photo, which agrees with the 30-round GEN M3's 1.07 in within its ±; the patent's tower is environment, drawn short at the top.
photo and patent differ by 0.285 in beyond what each states it is good to.
What seats it: the notch's upper edge hangs on the lower's catch. Two magazines for one catch and one bolt have it at one height under their lips: the 30-round GEN M3's is 1.07 in (magpul-pmag-30-gen-m3.catch_notch_top).
Hang below the magwell when seatedNo value yetMissingNo source yet
Onboarding checklist: Derived: overall_height minus the insertion depth, which is fixed by the mag-catch interface. Not entered: how far the drum stands under a lower depends on that lower's mouth; the part's test says it for the catalog's two (app/tests/magpul-pmag-d-60.test.ts).
Weight, loaded with 60 rounds46 oz ± 0.5 ozConfirmedPublished: Magpul, PMAG D-60 AR/M4 GEN M3 (MAG576), technical specifications, the maker, read Oct 6, 2026
Published “Weight, loaded ~46 oz.” used
Magpul, PMAG D-60 AR/M4 GEN M3 (MAG576), technical specifications, the maker, read Oct 6, 2026 the page, harvested Oct 6, 2026
Magpul's own page says about 46 oz; sellers quoting Magpul add 'M855 NATO' (Mile High Shooting, Midwest Gun Works: discovery's leads).
One round's share of Magpul's loaded weight0.42 oz ± 0.01 ozConfirmedWorked out: ({.weight_loaded} - {.weight}) / {.capacity}
Worked out 0.425 oz ± 0.01 oz used
({.weight_loaded} - {.weight}) / {.capacity}
What the loaded weight is worked out from in a build: Magpul's loaded figure less its empty one (which is with the dust cover: without it each round's share would be a little more), over its 60 rounds.
Length as the manufacturer states it (reference points undefined)7.4 in ± 0.05 in 188 mmConfirmedPublished: Magpul, PMAG D-60 AR/M4 GEN M3 (MAG576), technical specifications, the maker, read Oct 6, 2026
Published “Length, max 7.4 in.” used
Magpul, PMAG D-60 AR/M4 GEN M3 (MAG576), technical specifications, the maker, read Oct 6, 2026 the page, harvested Oct 6, 2026
Width as the manufacturer states it: across the drum, side to side4.1 in ± 0.05 in 104.1 mmConfirmedPublished: Magpul, PMAG D-60 AR/M4 GEN M3 (MAG576), technical specifications, the maker, read Oct 6, 2026
Published “Width, max: 4.1 in.” used
Magpul, PMAG D-60 AR/M4 GEN M3 (MAG576), technical specifications, the maker, read Oct 6, 2026 the page, harvested Oct 6, 2026
No page says what it is measured across. Settled on the photos: seen from the rear (9a2a10cb54cb) the widest row is across the drum's round body at the height of its axis (row 856 of 7 to 1187, 331 px above the lowest point, half the 654 px width being 327), not across the retaining clips at its corners, and the height to that width is 1.804, Magpul's 7.4 to 4.1 being 1.805: the 4.1 is the drum's diameter across the rifle. Its depth along the bore is less (drum_depth).
Capacity60ConfirmedPublished: Magpul, PMAG D-60 AR/M4 GEN M3 (MAG576), technical specifications, the maker, read Oct 6, 2026
Published “Capacity 60 rds” used
Magpul, PMAG D-60 AR/M4 GEN M3 (MAG576), technical specifications, the maker, read Oct 6, 2026 the page, harvested Oct 6, 2026
Feed tower, width side to side where it stands in the well0.875 in ± 0.022 in 22.2 mmProvisionalPhoto: the studio photo of the D-60 from the rear, square to the rear cover (as hosted by Sportsman's Warehouse, 1200 px)
Photo 0.875 in ± 0.022 in used
the studio photo of the D-60 from the rear, square to the rear cover (as hosted by Sportsman's Warehouse, 1200 px), harvested
Scale: scale from magpul-pmag-d-60.overall_height = 7.4 in (y-extent 1183 px → 159.9 px/in) and magpul-pmag-d-60.stated_width = 4.1 in (x-extent 657 px → 160.2 px/in), which agree within 0.2%; mean 160.1 px/in. Read by median row width in y [4.8, 6.4] (0.868–0.912) of the traced outline (tools/trace.py); the feed tower's width, side to side, where it stands in the magazine well
The feed tower's lean from the drum's two faces (with the tower upright the drum hangs nose up by this much)10° ± 2°ProvisionalPhoto: US D765,813 S (Magpul, 'Drum magazine for a firearm'), FIG. 4 left side elevation, 300 dpi
Photo 10 deg ± 2 deg used
US D765,813 S (Magpul, 'Drum magazine for a firearm'), FIG. 4 left side elevation, 300 dpi, harvested
Scale: an angle: the figure's own vertical, which the drum's two faces stand on. Read by the trace tool's reading of the spine's two broken lines as drawn: rear and front 10.0° from the vertical over 0.08 to 0.3 of the figure's height (tools/trace.py's edge lean, 2026-10-06); on a polygon picked along the tower's outline the spine reads 10.1°
The line itself reads to a tenth of a degree; the ± is for what it is a line of: the patent's broken-line tower, environment and drawn a little small and short against the product. In the patent's side elevations the drum's faces are upright and the tower leans forward as it rises. Magpul's and Primary Arms' pictures of it in a rifle (b79663b079db, 3f4a2e72a994) show the drum hanging nose up, its faces 10 to 15 degrees off square to the bore read by eye in perspective: the same way round, and no better than that.
A retaining clip's half width as an angle about the drum's axis, where it stands out of the rear cover's rim13.6° ± 1°ProvisionalPhoto: the studio photo of the D-60 from the rear, as hosted by Sportsman's Warehouse, 1200 px
Photo 13.6 deg ± 1 deg used
the studio photo of the D-60 from the rear, as hosted by Sportsman's Warehouse, 1200 px, harvested
Scale: the rear outline's placement (tools/trace.py): magpul-pmag-d-60.overall_height = 7.4 in and magpul-pmag-d-60.stated_width = 4.1 in, which agree within 0.2% (160.1 px/in). Read by the rear outline about the hub's centre (0, -5.375): it stands beyond 2.09 in from -58.7° to -31.7° (lower right) and from -149.4° to -122.1° (lower left): 27.0° and 27.3° across
The four clips are at the diagonals: the two lower ones are centred 45.2 and 44.3 degrees under the level through the hub; the two upper run into the roof's shoulders.
A retaining clip's outer face from the drum's axis, at the rear2.3 in ± 0.03 in 58.4 mmProvisionalPhoto: the studio photo of the D-60 from the rear, as hosted by Sportsman's Warehouse, 1200 px
Photo 2.3 in ± 0.03 in used
the studio photo of the D-60 from the rear, as hosted by Sportsman's Warehouse, 1200 px, harvested
Scale: the rear outline's placement (tools/trace.py): magpul-pmag-d-60.overall_height = 7.4 in and magpul-pmag-d-60.stated_width = 4.1 in, which agree within 0.2% (160.1 px/in). Read by the rear outline's greatest distance from the hub's centre over the two lower clips: 2.297 and 2.303 in (the upper two 2.347 and 2.351, where the roof's shoulders are behind them); the body's rim 2.05 at the level of the hub
The drum's axis (the rear cover's hub) below the feed lips' top, seen from the rear5.375 in ± 0.03 in 136.5 mmProvisionalPhoto: the studio photo of the D-60 from the rear, as hosted by Sportsman's Warehouse, 1200 px
Photo 5.375 in ± 0.03 in used
the studio photo of the D-60 from the rear, as hosted by Sportsman's Warehouse, 1200 px, harvested
Scale: the rear outline's placement (tools/trace.py): magpul-pmag-d-60.overall_height = 7.4 in and magpul-pmag-d-60.stated_width = 4.1 in, which agree within 0.2% (160.1 px/in). Read by the hub's rim picked as a circle of radius 111 px centred (611, 867.5), the silhouette's top at row 7: 860.5 px
The dot matrix: one square's side0.073 in ± 0.008 in 1.9 mmProvisionalPhoto: the studio photo of the D-60 from the rear, as hosted by Sportsman's Warehouse, 1200 px
Photo 0.073 in ± 0.008 in used
the studio photo of the D-60 from the rear, as hosted by Sportsman's Warehouse, 1200 px, harvested
Scale: the rear outline's scale, 160.1 px/in. Read by the first group's three squares on the photo enlarged 2.4 times: each 28 enlarged px (11.7 px), 7 between two (2.9 px)
Sixty squares, five rows of four groups of three, counted on the rear photo enlarged 2.4 times and on the patent's FIG. 3 (both show 5 by 12).
The dot matrix: the gap between two groups of three0.088 in ± 0.01 in 2.2 mmProvisionalPhoto: the studio photo of the D-60 from the rear, as hosted by Sportsman's Warehouse, 1200 px
Photo 0.088 in ± 0.01 in used
the studio photo of the D-60 from the rear, as hosted by Sportsman's Warehouse, 1200 px, harvested
Scale: the rear outline's scale, 160.1 px/in. Read by from the first group's last square to the second group's first: 34 enlarged px (14.2 px)
The drum standing as the patent draws it (its faces upright): from its lowest point to the top of the stop under the well4.487 in ± 0.056 in 114 mmProvisionalPhoto: US D765,813 S (Magpul, 'Drum magazine for a firearm'), FIG. 3 rear elevation, 300 dpi: the drum below the feed tower
Photo 4.487 in ± 0.056 in used
US D765,813 S (Magpul, 'Drum magazine for a firearm'), FIG. 3 rear elevation, 300 dpi: the drum below the feed tower, harvested
Scale: scale from magpul-pmag-d-60.stated_width = 4.1 in (x-extent 1209 px → 294.9 px/in). Read by height of the traced outline (tools/trace.py); the drum standing as the patent draws it, from its lowest point to the top of the stop under the well (the solid lines' top, the tower's broken lines cut off above it)
The drum along its own axis, from the rear cover's face to the loading lever's front3.595 in ± 0.05 in 91.3 mmCorroboratedPhoto: US D765,813 S (Magpul, 'Drum magazine for a firearm'), FIG. 4 left side elevation, 300 dpi: the drum below the feed tower
Photo 3.595 in ± 0.05 in used
US D765,813 S (Magpul, 'Drum magazine for a firearm'), FIG. 4 left side elevation, 300 dpi: the drum below the feed tower, harvested
Scale: scale from magpul-pmag-d-60.drum_height = 4.487 in (y-extent 1454 px → 324.0 px/in). Read by width of the traced outline (tools/trace.py); the drum along its own axis, from the rear cover's face to the loading lever's front
Photo 3.584 in ± 0.05 in
US D765,813 S (Magpul, 'Drum magazine for a firearm'), FIG. 6 top plan, 300 dpi, harvested
Scale: magpul-pmag-d-60.stated_width = 4.1 in over the figure's 1167 px across (columns 692 to 1859): 284.6 px/in. Read by the figure's rows 1215 to 2235, front to rear: 1020 px
Photo 3.592 in ± 0.05 in
US D765,813 S (Magpul, 'Drum magazine for a firearm'), FIG. 7 bottom plan, 300 dpi, harvested
Scale: magpul-pmag-d-60.stated_width = 4.1 in over the figure's 1250 px across (columns 643 to 1893): 304.9 px/in. Read by the figure's rows 1136 to 2231, front to rear: 1095 px
The side elevation is the view the drum's outline is traced from; the two plans, each scaled by the width on its own, agree with it within 0.011 in.
What no page states: the drum's depth along the bore, less than its 4.1 in across. Three of the patent's figures, each scaled by the 4.1 in on its own, give it within 0.011 in; the plans also have the body 4.06 in across near the rear cover and 3.64 near the front, which is the taper the side elevation's lower edge has (2.05 to 1.84 in of radius): the body is round about one axis.
Magazine catch notch (left side), its lower edge (the top of the block under it) below the feed lips' top1.35 in ± 0.04 in 34.3 mmProvisionalPhoto: the studio photo of the D-60 from the rear, square to the rear cover, as hosted by Sportsman's Warehouse, 1200 px
Photo 1.35 in ± 0.04 in used
the studio photo of the D-60 from the rear, square to the rear cover, as hosted by Sportsman's Warehouse, 1200 px, harvested
Scale: the rear outline's placement (tools/trace.py): magpul-pmag-d-60.overall_height = 7.4 in and magpul-pmag-d-60.stated_width = 4.1 in, which agree within 0.2% (160.1 px/in). Read by the block's flat top at rows 228 to 232 (the tower's left edge at column 535 there, 543 above it), the silhouette's top at row 7: 1.396 in below the top as the photo stands, square to the rear cover, the tower leaning away by tower_lean; down the tower's own length that is (1.396 - 0.067) / cos 10°, the 0.067 being how much lower the block's rear end (0.55 in ahead of the spine, as the GEN M3's) stands than the top's highest point (0.17 ahead) for the lean; ± 2 px, the lean's ± and those two places
The block that stands out of the tower's left side under the catch's window shows in profile on the rear photo: a flat top and a chamfer back into the side, as on Magpul's 30-round GEN M3 (whose window's lower edge is 1.32 in under its lips).
The block under the catch notch (left side), standing out of the side0.05 in ± 0.013 in 1.3 mmProvisionalPhoto: the studio photo of the D-60 from the rear, square to the rear cover, as hosted by Sportsman's Warehouse, 1200 px
Photo 0.05 in ± 0.013 in used
the studio photo of the D-60 from the rear, square to the rear cover, as hosted by Sportsman's Warehouse, 1200 px, harvested
Scale: the rear outline's placement (tools/trace.py): magpul-pmag-d-60.overall_height = 7.4 in and magpul-pmag-d-60.stated_width = 4.1 in, which agree within 0.2% (160.1 px/in). Read by the tower's left edge at column 535 across the block's top and 543 above and below it: 8 px; ± 2 px
Not drawn (as on the 30-round, whose reading is 0.054 in: a body as wide as the well with this on it would stand in the well's left wall under the catch's slot).
The feed lips' top above the upper edge of the collar round the tower's foot, as the magazine stands with its drum's faces upright2.852 in ± 0.03 in 72.4 mmProvisionalPhoto: the studio photo of the D-60 from the rear, square to the rear cover, as hosted by Sportsman's Warehouse, 1200 px
Photo 2.852 in ± 0.03 in used
the studio photo of the D-60 from the rear, square to the rear cover, as hosted by Sportsman's Warehouse, 1200 px, harvested
Scale: the rear outline's placement (tools/trace.py): magpul-pmag-d-60.overall_height = 7.4 in and magpul-pmag-d-60.stated_width = 4.1 in, which agree within 0.2% (160.1 px/in). Read by the collar's upper edge at row 462 (the step out from the tower's sides), the silhouette's top at row 7; the patent's drum, scaled by the 4.1 in width, has the stop under the well at the same height above its lowest point (drum_height 4.487 in, the photo's collar 4.539)
The feed tower's spine, its rear face where it meets the stop on the drum's roof, ahead of the drum's rearmost point (the drum's faces upright)0.086 in ± 0.03 in 2.2 mmProvisionalPhoto: US D765,813 S (Magpul, 'Drum magazine for a firearm'), FIG. 4 left side elevation, 300 dpi
Photo 0.086 in ± 0.03 in used
US D765,813 S (Magpul, 'Drum magazine for a firearm'), FIG. 4 left side elevation, 300 dpi, harvested
Scale: the drum outline's scale (tools/trace.py): magpul-pmag-d-60.drum_height = 4.487 in over 1454 px, 324.0 px/in, the height handed on from FIG. 3 scaled by magpul-pmag-d-60.stated_width = 4.1 in. Read by the spine's outer broken line meets the stop's top at column 1808 (row 1385), the figure's rearmost column being 1836: 28 px; ± 3 px and what a broken line leaves
Where the tower stands on the drum, fore and aft: only the patent's broken lines show it from the side.
The seam between the rear cover and the main body, ahead of the drum's rearmost point (along the drum's axis)0.59 in ± 0.02 in 15 mmProvisionalPhoto: US D765,813 S (Magpul, 'Drum magazine for a firearm'), FIG. 4 left side elevation, 300 dpi
Photo 0.59 in ± 0.02 in used
US D765,813 S (Magpul, 'Drum magazine for a firearm'), FIG. 4 left side elevation, 300 dpi, harvested
Scale: the drum outline's scale (tools/trace.py): magpul-pmag-d-60.drum_height = 4.487 in over 1454 px, 324.0 px/in, the height handed on from FIG. 3 scaled by magpul-pmag-d-60.stated_width = 4.1 in. Read by the full-height line at column 1645 (dark over all of rows 1650 to 2650), the figure's rearmost column 1836: 191 px
The seam between the main body and the front cover, ahead of the drum's rearmost point (along the drum's axis)2.667 in ± 0.02 in 67.7 mmProvisionalPhoto: US D765,813 S (Magpul, 'Drum magazine for a firearm'), FIG. 4 left side elevation, 300 dpi
Photo 2.667 in ± 0.02 in used
US D765,813 S (Magpul, 'Drum magazine for a firearm'), FIG. 4 left side elevation, 300 dpi, harvested
Scale: the drum outline's scale (tools/trace.py): magpul-pmag-d-60.drum_height = 4.487 in over 1454 px, 324.0 px/in, the height handed on from FIG. 3 scaled by magpul-pmag-d-60.stated_width = 4.1 in. Read by the full-height line at column 972 (dark over 750 of rows 1650 to 2650), the figure's rearmost column 1836: 864 px
A retaining clip's hook on the rear cover: its inner end from the drum's axis1.56 in ± 0.04 in 39.6 mmProvisionalPhoto: the studio photo of the D-60 from the rear, square to the rear cover, as hosted by Sportsman's Warehouse, 1200 px
Photo 1.56 in ± 0.04 in used
the studio photo of the D-60 from the rear, square to the rear cover, as hosted by Sportsman's Warehouse, 1200 px, harvested
Scale: the rear outline's placement (tools/trace.py): magpul-pmag-d-60.overall_height = 7.4 in and magpul-pmag-d-60.stated_width = 4.1 in, which agree within 0.2% (160.1 px/in). Read by the upper right clip's inner edge on the photo enlarged 2.4 times: 599 enlarged px from the hub's centre along the diagonal (250 px)
Feed tower, the spine's width (the rib down its rear face that runs in the well's slot)0.46 in ± 0.02 in 11.7 mmProvisionalPhoto: the studio photo of the D-60 from the rear, square to the rear cover, as hosted by Sportsman's Warehouse, 1200 px
Photo 0.46 in ± 0.02 in used
the studio photo of the D-60 from the rear, square to the rear cover, as hosted by Sportsman's Warehouse, 1200 px, harvested
Scale: the rear outline's scale, 160.1 px/in. Read by the raised middle of the tower's rear face between its two dark edges, columns 576 to 650 on rows 150 to 440 (73 to 75 px)
Under the well's slot for it (std.ar15.magwell_spine_slot_width, 0.470).
Feed tower, the gap between the two feed lips, seen from the rear0.44 in ± 0.02 in 11.2 mmProvisionalPhoto: the studio photo of the D-60 from the rear, square to the rear cover, as hosted by Sportsman's Warehouse, 1200 px
Photo 0.44 in ± 0.02 in used
the studio photo of the D-60 from the rear, square to the rear cover, as hosted by Sportsman's Warehouse, 1200 px, harvested
Scale: the rear outline's scale, 160.1 px/in. Read by the lips' inner faces at columns 578 and 648 on rows 10 to 50 (the photo is of a loaded magazine: a round's base fills the left of the gap)
Feed tower, the gap between the feed lips: its floor below the lips' top, seen from the rear0.31 in ± 0.03 in 7.9 mmProvisionalPhoto: the studio photo of the D-60 from the rear, square to the rear cover, as hosted by Sportsman's Warehouse, 1200 px
Photo 0.31 in ± 0.03 in used
the studio photo of the D-60 from the rear, square to the rear cover, as hosted by Sportsman's Warehouse, 1200 px, harvested
Scale: the rear outline's scale, 160.1 px/in. Read by the gap's right half is open down to row 56, the silhouette's top at row 7: 49 px
What shows of a loaded magazine: the floor is the next round or the follower, not a face of the tower.
The front cover's hub: the round face at its middle, radius0.495 in ± 0.01 in 12.6 mmProvisionalPhoto: US D765,813 S (Magpul, 'Drum magazine for a firearm'), FIG. 2 front elevation, 300 dpi
Photo 0.495 in ± 0.01 in used
US D765,813 S (Magpul, 'Drum magazine for a firearm'), FIG. 2 front elevation, 300 dpi, harvested
Scale: magpul-pmag-d-60.stated_width = 4.1 in over the figure's 1216 px across the drum (columns 627 to 1843): 296.6 px/in; radii about the hub's centre (1236, 2127), which is 607 px above the figure's lowest point: half the width. Read by the dark pixels' distances from the centre, in rings 2 px wide: a full circle at 146 to 148 px
The front cover's circles are read on the patent's front elevation as lines: which way each steps is in no view in profile (the model cuts each as a groove of one depth).
The front cover's hub: the ring round its middle face, outer radius0.607 in ± 0.01 in 15.4 mmProvisionalPhoto: US D765,813 S (Magpul, 'Drum magazine for a firearm'), FIG. 2 front elevation, 300 dpi
Photo 0.607 in ± 0.01 in used
US D765,813 S (Magpul, 'Drum magazine for a firearm'), FIG. 2 front elevation, 300 dpi, harvested
Scale: magpul-pmag-d-60.stated_width = 4.1 in over the figure's 1216 px across the drum (columns 627 to 1843): 296.6 px/in; radii about the hub's centre (1236, 2127), which is 607 px above the figure's lowest point: half the width. Read by a full circle at 180 px (and one at 168 to 170 inside it)
The front cover: the circle round its dished face, radius1.038 in ± 0.01 in 26.4 mmProvisionalPhoto: US D765,813 S (Magpul, 'Drum magazine for a firearm'), FIG. 2 front elevation, 300 dpi
Photo 1.038 in ± 0.01 in used
US D765,813 S (Magpul, 'Drum magazine for a firearm'), FIG. 2 front elevation, 300 dpi, harvested
Scale: magpul-pmag-d-60.stated_width = 4.1 in over the figure's 1216 px across the drum (columns 627 to 1843): 296.6 px/in; radii about the hub's centre (1236, 2127), which is 607 px above the figure's lowest point: half the width. Read by a full double circle at 306 to 308 px (further out, arcs at 364 to 370 and 422 to 434 px that the lever and the clips break)
What it goes with
By the way it mounts, and the figures each part on file states: a part whose figures say it doesn't fit is left out, and one whose fit can't be checked from what is published is marked. A check is against published figures, not a guarantee.
AR-15 magazine well
- Lower receivers
- Aero Precision M4E1 complete lower, A2 grip and M4 stock, Aero Precision M4E1 Stripped Lower Receiver, Battle Arms Development Workhorse stripped lower, BCM MK2 AR-15 Lower Receiver, Bear Creek Arsenal BC-15 Multi Caliber, Lower Receiver, Black Anodized, Geissele Automatics Super Duty AR-15 Lower Receiver - Stripped Lower, Palmetto State Armory AR-15 "Stealth" Stripped Lower Receiver
Prices on file
Each seller's latest reading of its own page: before tax and shipping, and not a quote. The pages are read again every night.
- KYGUNCO $102.99 Nov 21, 2026, in stock that day
- Primary Arms $113.01 Nov 21, 2026, in stock that day
- GRITR Sports $116.99 Nov 21, 2026, in stock that day
- Midwest Gun Works $131.95 Nov 21, 2026, in stock that day
- Impact Guns $132.95 Nov 21, 2026, in stock that day
- Mile High Shooting Accessories $132.95 Nov 21, 2026, in stock that day
- MidwayUSA $132.95 Nov 21, 2026, in stock that day
- Scheels $132.99 Oct 6, 2026, in stock that day
- Right To Bear $134.95 Nov 21, 2026, in stock that day
- Magpul $139.95 Nov 21, 2026, stock not said
- Sportsman's Warehouse $139.99 Nov 21, 2026, in stock that day
- AR15Discounts $128.20 Nov 21, 2026, out of stock that day
- Rifle Supply $139.95 Nov 21, 2026, out of stock that day