Gas tube
Aero Precision Gas tube, mid-length, stainless steel
Aero Precision's mid-length stainless gas tube, 11.75 in, with its roll pin.

- Weight
- 0.64 oz ± 0.005 oz Confirmedpublished: Aero Precision, Gas Tube, Mid-Length - Stainless Steel (APRH100144C), Specifications, the maker, read Oct 2, 2026
- Lowest price
- $20.00 at Aero Precision, read Nov 21, 2026
- Maker's number
- APRH100144C
- Colour
- Natural stainless
- Drawn as
- modelled
- Maker's page
- aeroprecisionusa.com
In “Aero 5.56 carbine”, a build on the start page, as it is.
Its figures
Every figure the site draws and checks it by, with where it came from. Open one for each source's reading, and why one is used where they differ.
Length11.75 in ± 0.01 in 298.4 mmConfirmedPublished: Aero Precision, Gas Tube, Mid-Length - Stainless Steel (APRH100144C), Features, the maker, read Oct 2, 2026
Published “11.75"” used
Aero Precision, Gas Tube, Mid-Length - Stainless Steel (APRH100144C), Features, the maker, read Oct 2, 2026 the page, harvested Oct 2, 2026
Aero's feature list says only "11.75"" on the page of a tube it names mid-length; the discovery report found the same figure labelled on the Melonite tube's page ("Mid-Length 11.75"").
Outside diameter0.18 in ± 0.002 in 4.6 mmConfirmedStandard: US Army TDP drawing 8448567 (Gas Tube Assembly), PDF page 144, both ends
Standard “.1800 DIA REF” used
US Army TDP drawing 8448567 (Gas Tube Assembly), PDF page 144, both ends
A REF figure, the tube stock's size; .179 is allowed at its bends.
Aero gives none; the tube is the standard's (the key's socket takes a .180 tube).
How far the tube drops at its bend (its rear run above its front)0.156 in ± 0.01 in 4 mmConfirmedStandard: US Army TDP drawing 8448567 (Gas Tube Assembly), rev F (the rifle's tube; R 1.50 ±.50); user-supplied scan, PDF page 144
Standard “offset .156” used
US Army TDP drawing 8448567 (Gas Tube Assembly), rev F (the rifle's tube; R 1.50 ±.50); user-supplied scan, PDF page 144, from the site owner
Photo 0.17 in ± 0.02 in
Aero's gallery: the tube from the side, 1000 x 630, harvested
Scale: its published length over the silhouette's 831 px: 70.7 px/in. Read by the straight runs' centres, px rows 302.5 (rear) and 314.5 (front)
Photo 0.163 in ± 0.006 in
Aero's gallery: the tube from the side, the plugged front end at the right, 1000 x 630; a419898ca923 is the same photograph on a square ground and reads the same, harvested
Scale: its published length between the end faces, 831.2 px (columns 86.5 to 917.7 at the 225 level): 70.7 px/in, a pixel 0.014 in. Read by a level run, a round, a straight slope, an equal round and a level run fitted to the centre line (each column's upper and lower edge at the 200 and 225 levels, both copies): the drop reads 0.1632, 0.1619, 0.1641 and 0.1625
The 0.17 above is the same photo by two rows picked by eye.
The drawing; the photo agrees. It takes the tube from the receiver's .781 down to the block's .625.
The radius of each of the bend's two rounds, at the tube's centre line4.2 in ± 0.4 in 106.7 mmProvisionalPhoto: Aero's gallery: the tube from the side, the plugged front end at the right, 1000 x 630; a419898ca923 is the same photograph on a square ground and reads the same
Photo 4.2 in ± 0.4 in used
Aero's gallery: the tube from the side, the plugged front end at the right, 1000 x 630; a419898ca923 is the same photograph on a square ground and reads the same, harvested
Scale: its published length between the end faces, 831.2 px (columns 86.5 to 917.7 at the 225 level): 70.7 px/in, a pixel 0.014 in. Read by a level run, a round, a straight slope, an equal round and a level run fitted to the centre line with the radius left free: 4.00 and 4.34 (edges at the 200 and 225 levels), 4.39 and 4.38 in the other copy; the slope between the rounds 6.25 to 6.3 degrees and 1.0 in long, the fit's rms 0.8 thousandths
With the radius held at the drawing's 1.50 the fit is six tenths worse (1.3 to 1.4 thousandths rms) and puts the bend from 3.71 to 3.75 and 5.44 to 5.48. At the 240 level the edges take in the tube's shadow and the fit is three times worse: left out.
The Army's drawing is of the rifle's tube ("1.50 ±.50 R 2 PLACES", 8448567; the callout is read in the carbine tube's ledger, bend_radius); where and how a mid-length tube bends is on no drawing on file, so this tube's own photo is the reading. The carbine tube's photos read 3.6.
Where the bend begins, from the tube's rear (receiver) end3.61 in ± 0.03 in 91.7 mmConflictPhoto: Aero's gallery: the tube from the side, the plugged front end at the right, 1000 x 630; a419898ca923 is the same photograph on a square ground and reads the same
Photo 3.86 in ± 0.05 in
Aero's gallery: the tube from the side, 1000 x 630, harvested
Scale: 70.7 px/in. Read by where the silhouette leaves the rear run, px 360 (the roll-pin end, at the right, is the front)
The rifle's tube bends at 4.16 ±.25 (8448567); this is the mid-length's. Where the eye sees it leave: the fitted centre line is a twentieth of the drop off the rear run at 3.89.
Photo 3.61 in ± 0.03 in used
Aero's gallery: the tube from the side, the plugged front end at the right, 1000 x 630; a419898ca923 is the same photograph on a square ground and reads the same, harvested
Scale: its published length between the end faces, 831.2 px (columns 86.5 to 917.7 at the 225 level): 70.7 px/in, a pixel 0.014 in. Read by where the first round leaves the rear run in the fit of bend_radius (radius free): 3.607 and 3.629, 3.584 and 3.621 in the other copy; the plain end is the rear, the end with the cross hole the front
The carbine tube's own photos put its bend at 3.71: the same place from the rear end, as it has to be to clear the same barrel nut.
Where a round of the fitted radius is tangent to the rear run, which is what the model's centre line is built from; the 3.86 is where the tube is seen to have left the run, a quarter of an inch on along a round this gentle. Two definitions of one bend, not two bends (2026-10-13).
photo and photo-fit differ by 0.25 in beyond what each states it is good to.
Where the bend ends, from the tube's rear (receiver) end5.56 in ± 0.03 in 141.2 mmCorroboratedPhoto: Aero's gallery: the tube from the side, the plugged front end at the right, 1000 x 630; a419898ca923 is the same photograph on a square ground and reads the same
Photo 5.49 in ± 0.05 in
Aero's gallery: the tube from the side, 1000 x 630, harvested
Scale: 70.7 px/in. Read by where the silhouette joins the front run, px 475
Photo 5.56 in ± 0.03 in used
Aero's gallery: the tube from the side, the plugged front end at the right, 1000 x 630; a419898ca923 is the same photograph on a square ground and reads the same, harvested
Scale: its published length between the end faces, 831.2 px (columns 86.5 to 917.7 at the 225 level): 70.7 px/in, a pixel 0.014 in. Read by where the second round joins the front run in the fit of bend_radius (radius free): 5.534 and 5.576, 5.551 and 5.583 in the other copy
The carbine tube's: 5.53. The centre line is halfway down the drop 4.57 to 4.62 in from the rear end.
The fitted round's tangent point, as bend_start_from_rear.
The gas hole's centre behind the tube's front end0.605 in ± 0.004 in 15.4 mmConfirmedWorked out: {std.ar15.gas_tube_hole_from_front}
Worked out 0.605 in ± 0.004 in used
{std.ar15.gas_tube_hole_from_front}, from the site owner
The Army's drawing 8448567, ".605 REF".
Where this tube touches the block: its hole over the block's port. The part's frame is here. This tube's photo doesn't show the hole (it faces the barrel, and the lower edge has no notch a pixel deep there); the carbine tube's photos show its own at 0.607.
The gas hole's diameter0.125 in ± 0.003 in 3.2 mmConfirmedWorked out: {aero-carbine-gas-tube.gas_hole_d}
Worked out 0.125 in ± 0.003 in used
{aero-carbine-gas-tube.gas_hole_d}, from the site owner
The Army's drawing 8448567, ".125 DIA +.003 THRU THIS SIDE ONLY TO DEPTH SHOWN": its source is in the carbine tube's ledger.
The roll pin's hole behind the tube's front end0.187 in ± 0.003 in 4.7 mmConfirmedWorked out: {aero-carbine-gas-tube.pin_hole_from_front}
Worked out 0.187 in ± 0.003 in used
{aero-carbine-gas-tube.pin_hole_from_front}, from the site owner
The Army's drawing 8448567, ".187 ±.003": its source is in the carbine tube's ledger.
Photo 0.2 in ± 0.015 in
Aero's gallery: the tube from the side, the plugged front end at the right, 1000 x 630; a419898ca923 is the same photograph on a square ground and reads the same, harvested
Scale: its published length between the end faces, 831.2 px (columns 86.5 to 917.7 at the 225 level): 70.7 px/in, a pixel 0.014 in. Read by the white ground seen through the cross hole on the tube's middle rows (level 248 to 254 where the tube beside it is 220 to 230): four columns, 0.183 to 0.225 in from the front end face, their weighted middle 0.200
Seen straight through from the side: the pin lies across the rifle, square to the plane of the bend.
The drawing; the photo agrees within a pixel.
The roll pin's hole, diameter0.078 in ± 0.003 in 2 mmConfirmedWorked out: {aero-carbine-gas-tube.pin_hole_d}
Worked out 0.078 in ± 0.003 in used
{aero-carbine-gas-tube.pin_hole_d}, from the site owner
The Army's drawing 8448567, ".078 DIA +.003 THRU": its source is in the carbine tube's ledger. In this photo the hole is four columns of white, 0.06 in.
The front groove round the plugged end, its middle from the front end0.088 in ± 0.015 in 2.2 mmProvisionalPhoto: Aero's gallery: the tube from the side, the plugged front end at the right, 1000 x 630; a419898ca923 is the same photograph on a square ground and reads the same
Photo 0.088 in ± 0.015 in used
Aero's gallery: the tube from the side, the plugged front end at the right, 1000 x 630; a419898ca923 is the same photograph on a square ground and reads the same, harvested
Scale: its published length between the end faces, 831.2 px (columns 86.5 to 917.7 at the 225 level): 70.7 px/in, a pixel 0.014 in. Read by where the tube reads thinnest, column by column, near its front end: the two columns at 0.081 and 0.095 in from the end face at the 225 level (10.4 px where the columns beside them are 11.1 to 11.4), 0.073 and 0.087 at the 200 level, 0.084 and 0.098 at 235
The tube is closed at the front by a plug held by two grooves pressed round it, one each side of the pin's hole (the Army's drawing shows them and gives them no figure; the carbine tube's ledger has the note). Read on this tube's own photo; the carbine tube's read 0.08 and 0.295.
The rear groove round the plugged end, its middle from the front end0.293 in ± 0.02 in 7.4 mmProvisionalPhoto: Aero's gallery: the tube from the side, the plugged front end at the right, 1000 x 630; a419898ca923 is the same photograph on a square ground and reads the same
Photo 0.293 in ± 0.02 in used
Aero's gallery: the tube from the side, the plugged front end at the right, 1000 x 630; a419898ca923 is the same photograph on a square ground and reads the same, harvested
Scale: its published length between the end faces, 831.2 px (columns 86.5 to 917.7 at the 225 level): 70.7 px/in, a pixel 0.014 in. Read by where the tube reads thinnest behind the pin's hole: the columns at 0.279, 0.293 and 0.307 in from the end face at the 225 level (10.0, 10.4 and 9.2 px where the tube behind is 10.6), 0.272 to 0.300 at the 200 level, 0.296 and 0.310 at 235
Three columns with the middle one the least thin: one groove with a glint in it, or two closer than the picture can part. One is drawn.
A groove's width along the tube0.035 in ± 0.015 in 0.9 mmProvisionalPhoto: Aero's gallery: the tube from the side, the plugged front end at the right, 1000 x 630; a419898ca923 is the same photograph on a square ground and reads the same
Photo 0.035 in ± 0.015 in used
Aero's gallery: the tube from the side, the plugged front end at the right, 1000 x 630; a419898ca923 is the same photograph on a square ground and reads the same, harvested
Scale: its published length between the end faces, 831.2 px (columns 86.5 to 917.7 at the 225 level): 70.7 px/in, a pixel 0.014 in. Read by the columns over which the tube reads thinner than beside the groove: two columns of 0.014 in at the front groove, three at the rear
Two to three pixels: a groove this narrow is as wide as the photo's blur.
A groove's depth, as the diameter it takes off0.012 in ± 0.006 in 0.3 mmProvisionalPhoto: Aero's gallery: the tube from the side, the plugged front end at the right, 1000 x 630; a419898ca923 is the same photograph on a square ground and reads the same
Photo 0.012 in ± 0.006 in used
Aero's gallery: the tube from the side, the plugged front end at the right, 1000 x 630; a419898ca923 is the same photograph on a square ground and reads the same, harvested
Scale: its published length between the end faces, 831.2 px (columns 86.5 to 917.7 at the 225 level): 70.7 px/in, a pixel 0.014 in. Read by how much thinner the tube reads at a groove than on the tube beside it: 0.7 to 1.0 px at the front groove, 0.6 to 1.4 px at the rear
A pixel's blur fills a groove this narrow: it is at least this deep. The carbine tube's four photos read 0.011.
The head at the tube's rear end, its length0.1 in ± 0.02 in 2.5 mmProvisionalPhoto: Aero's gallery: the tube from the side, the plugged front end at the right, 1000 x 630; a419898ca923 is the same photograph on a square ground and reads the same
Photo 0.1 in ± 0.02 in used
Aero's gallery: the tube from the side, the plugged front end at the right, 1000 x 630; a419898ca923 is the same photograph on a square ground and reads the same, harvested
Scale: its published length between the end faces, 831.2 px (columns 86.5 to 917.7 at the 225 level): 70.7 px/in, a pixel 0.014 in. Read by the columns from the rear end face over which the tube reads thicker than behind it: 10.7 to 10.9 px to 0.078 in, 10.6 at 0.092 and 10.4 from 0.106 on at the 225 level; 11.4 to 11.6 px to 0.081, 11.2 at 0.095 and 10.7 from 0.109 on at 235
The carbine tube's four photos: 0.1. Drawn at the tube's diameter, as the carbine tube's is.
The end that enters the carrier key. The drawing shows the head and gives its length no figure.
The broken rim of each end face, along the tube and across it0.012 in ± 0.008 in 0.3 mmProvisionalPhoto: Aero's gallery: the tube from the side, the plugged front end at the right, 1000 x 630; a419898ca923 is the same photograph on a square ground and reads the same
Photo 0.012 in ± 0.008 in used
Aero's gallery: the tube from the side, the plugged front end at the right, 1000 x 630; a419898ca923 is the same photograph on a square ground and reads the same, harvested
Scale: its published length between the end faces, 831.2 px (columns 86.5 to 917.7 at the 225 level): 70.7 px/in, a pixel 0.014 in. Read by how much thinner the tube reads in the first column from each end face than two columns in: 0.6 to 0.9 px at the front, 1.5 to 3 px at the rear, within 0.014 in of the face
A pixel: as large as the picture's blur, and the rear end's the larger, as on the carbine tube. Drawn as a chamfer this size at both ends.
Where the thinner stretch behind the head ends, from the tube's rear end2.31 in ± 0.04 in 58.7 mmProvisionalPhoto: Aero's gallery: the tube from the side, the plugged front end at the right, 1000 x 630; a419898ca923 is the same photograph on a square ground and reads the same
Photo 2.31 in ± 0.04 in used
Aero's gallery: the tube from the side, the plugged front end at the right, 1000 x 630; a419898ca923 is the same photograph on a square ground and reads the same, harvested
Scale: its published length between the end faces, 831.2 px (columns 86.5 to 917.7 at the 225 level): 70.7 px/in, a pixel 0.014 in. Read by the tube's rows, column by column from the rear end: their darkest level is 111 to 116 as far as 2.30 in and 94 to 101 from 2.34 on, with the edges broken up over the five columns between (2.285 to 2.384)
Between its head and this station the tube is thinner than ahead of it: a line across the tube in the photo, with a different sheen behind it. The carbine tube has the same at 2.27.
How much thinner the stretch behind the head is than the tube ahead of it, on the diameter0.008 in ± 0.004 in 0.2 mmProvisionalPhoto: Aero's gallery: the tube from the side, the plugged front end at the right, 1000 x 630; a419898ca923 is the same photograph on a square ground and reads the same
Photo 0.008 in ± 0.004 in used
Aero's gallery: the tube from the side, the plugged front end at the right, 1000 x 630; a419898ca923 is the same photograph on a square ground and reads the same, harvested
Scale: its published length between the end faces, 831.2 px (columns 86.5 to 917.7 at the 225 level): 70.7 px/in, a pixel 0.014 in. Read by the median thickness over 0.2 to 2.1 in from the rear end against that over 2.4 to 3.4 in: 0.61, 0.41 and 0.56 px less at the 200, 225 and 235 levels
Half a pixel, the same way at three levels; the carbine tube's four photos, at finer scales, read 0.013. Which of the two stretches is the drawing's .180 isn't read: the head and the tube ahead of the relief are drawn at it, and the relief this much under.
The plug in the front end, its length from the front end face0.44 in ± 0.03 in 11.2 mmConfirmedWorked out: {aero-carbine-gas-tube.plug_length}
Worked out 0.44 in ± 0.03 in used
{aero-carbine-gas-tube.plug_length}, from the site owner
The Army's drawing 8448567, the view from below, scaled: the reading is in the carbine tube's ledger. It ends ahead of the gas hole's front edge (0.54 from the end), as it must.
Where the tube's bore ends. Not a callout: the plug's own drawing (8448568) isn't in the package.
The tube's bore0.13 in ± 0.003 in 3.3 mmProvisionalWorked out: The bore of a plain tube of this length (11.75 in) and diameter (.180) that weighs Aero's 0.64 oz as stainless steel at std.density.stainless_416 (127 g to the cubic inch): 18.14 g is 0.1429 cubic inches, a wall of 0.01216 square inches, which leaves a bore of 0.1301. By the weight's half digit (0.635 to 0.645 oz): 0.1306 to 0.1296; as a 304 stainless, 2 percent denser: 0.131. The plug, the relief and the holes are left out of it.
Worked out 0.13 in ± 0.003 in used
The bore of a plain tube of this length (11.75 in) and diameter (.180) that weighs Aero's 0.64 oz as stainless steel at std.density.stainless_416 (127 g to the cubic inch): 18.14 g is 0.1429 cubic inches, a wall of 0.01216 square inches, which leaves a bore of 0.1301. By the weight's half digit (0.635 to 0.645 oz): 0.1306 to 0.1296; as a 304 stainless, 2 percent denser: 0.131. The plug, the relief and the holes are left out of it., harvested
Aero names no grade of stainless. It shows only at the tube's open rear end, inside the receiver.
No page and no callout gives it. The Army's section as drawn, without a figure, has 0.09 (the reading is in the carbine tube's ledger, bore); a tube with that bore would weigh 1.0 oz at this length, and Aero says 0.64. The carbine tube's own weight (0.5 oz, given to a tenth) leaves 0.134.
What it goes with
By the way it mounts, and the figures each part on file states: a part whose figures say it doesn't fit is left out, and one whose fit can't be checked from what is published is marked. A check is against published figures, not a guarantee.
Gas tube
- Gas blocks
- Aero Precision .750 low profile gas block, BCM Front Sight Base F - FSB (ID .750) - Milspec for Flat Top Uppers, BCM Low Profile Gas Block (steel with set screws) 625, BCM Low Profile Gas Block (steel with set screws) 750, SLR Rifleworks Sentry 7 Set Screw Adjustable Gas Block, Superlative Arms .750" Adjustable Gas Block, Bleed Off - Set Screw
Gas system length
- Barrels
- Aero Precision 16" 5.56 CMV barrel, mid-length, BCM Standard 14.5" Mid Length Barrel, Stripped, BCM Standard 16" Mid Length Barrel, Stripped, Bear Creek Arsenal BC-15 5.56 NATO, 16" Parkerized M4 Barrel, 1:7 Twist, Mid-Length Gas System, Faxon Firearms Duty Series Pencil Profile 16" Mid-Length 5.56 NATO AR15 Barrel, Geissele Automatics CHF Chrome Lined Barrel - 5.56 - 13.9", Geissele Automatics CHF Chrome Lined Barrel - 5.56 - 14.5", Geissele Automatics CHF Chrome Lined Barrel - 5.56 - 16"
Prices on file
Each seller's latest reading of its own page: before tax and shipping, and not a quote. The pages are read again every night.
- Aero Precision $20.00 Nov 21, 2026, stock not said